Search:

All the boards at the same time. My idea was to at least see the machine running. Then swap controller, power supply and control board (and deal with the codes after). I knew for sure the MFPB was...

All the boards were swapped together. Including the small one under developing units and the display). My logic was it should start because I know for sure the donor is working. But nothing, not even...

No, I swapped the board with it's own ssd board. All boards are matched, since they came from the same machine. That is what puzzles me. It should at least do something. But no.

Changed all boards (power supply mfpb, controller eMMC scanner and control board). Those boards came from a working machine so it should at least boot and throw some error codes. With all the boards...

It's not about repairing the machine to use it again. I somehow got some spare time and some C364 with over 1.5 mil pages sitting aroumd, waiting to be sent to recycling plant so I have spares. I was...

Hello guys. Got a C364 that received a lighting strike through the customer's network (at least that is what I figured since almost he's entire network -switches and router was fried). Changed power...

Bent scaner bed. Remove covers from left side of scaner (white cover), remove left side cover (T shape cover, black, 3 screws, it's the vertical one in the back, left side of machine). Under there...

Looks like the CMY unit are over they life span, or even worse, reseted. Don't reset any consumable on C227as they will go berserk very fast. It's better to hide the end life message and run them...

After waiting almost 10 days for KM to deliver the brushes, yesterday I finally got to the client and install them. And it works perfectly.
Thank you all for advices and a big thank you to...

When dealing with trouble codes search google for that code, like bizhub c-xxxx error code and trust the answer on the printcopy.info site. They are what the service manual says. Stay away from...

Thanks! Just for my education, what indicates that on the Configuration printout?

It is not enabled. Not knowing any better, I tried to enable it last week. Then the machine booted with errors....

If the fuser is heavy on the gears it might throw a 2152 error. Also, check if the door is closing properly and the lever that engages the gearbox is pressed firmly.
LE: if you "cheat" the door...

When you say "isolated network" you mean a router and a laptop different from the customer network? If that is the case and scans still don't arrive, it might be an issue with the printer. From what...

It doesn't have wi-fi

It is discontinued but I have it on an Android 9 device and works ok. KM print is the new app with support for newer models (although I printed with Pagescope on 368 series without problems, only...

Use Pagescope Mobile from Konica Minolta. The phone need to be on the same network as the printer (wireless ofcourse). If that's not possible (no wi-fi on site) than you can not.

Many technicians have disassembled copiers. But we are from all over the world. I have that cover and even can give it to you for free, because I don't think I will ever need to replace that. The...

As @copyman said, print a configuration page (utility-user settings-printer settings-print reports-configuration page). Or look in administrator-network settings, you should have two sets of...

Under the registration roller there is a sensor (you'll have to take all that assembly out and the transfer belt). Check if it's dirty, clean the actuator and slightly bend it's spring so it will put...

I did set that. Also lowered the fusing temperature by 10 degrees and it is better, but still have issues

Thanks alot. Was thinking of that because before it goes bananas the sheet looks like it's hovering for a second, but yeah, there is some dismantling to reach them. I'll order a couple of those...

Hi everyone. I have a FS-532 on a bizhub press 1052 recently bought by a client. Everything seemed to work fine until the customer complained about the finisher not stacking/exiting the paper...

Hi guys, please help, i'm stuck. I have a C224e with dead
control panel. No leds, no signs of life whatsoever. The leds from the mfpb are also dead. Changed the power supply, found that the old one...

Count me too when thanking 😁
Although the manual said to let the machine read the chart twice, it was as Synthohol said. Did it 3 timea each and the machine is ok.
The weird part is that it asked...

Blackcat4866, it didn't really 😆
But the client wants his c200. So at the
end he'll pay the bill. Tomorrow I'll do
the installation steps (again), hopefully
it will work.
Thanks for the answers...