both devices run same speed and same settings yet one works fine other offsets by that i mean rubbs off from print job (labels)
Type: Posts; User: The_man
both devices run same speed and same settings yet one works fine other offsets by that i mean rubbs off from print job (labels)
Hi, have 2 IMC3000 on same network same pc, 1 prints labels from bypass fine, other offsets, identical tray and paper settings, pc seems to overide any settings made prior to printing either on pc or...
hi thanks for reply have fitted egb, ctrl and psu still the same, looking like a service swap out.
Firstly, suspected pcdu, swapped with working pcdu, still the same. Tried pcdu reset.
Fitted 2 new connetors, as tend to bend when forced.
Suspect bicu now, unless anyone had this.
Thanks for all the replies been building quite a few of these models now to incorporate Equitrac, you do get used to them eventually, the longest menu to find initially was the keyboard alteration...
Hi IM C300 has different menus to retro devices and was wondering it there is a SP code to turn back new menus to the original type menu layout likes of IMC3000. Though search facility on IM C300...
Update, all ok for now suspect the aluminium ITB roller just above Yellow PCDU, bearings were a little stiff and causing belt to stall and touch drum.
These are the cause.. D2416346 and D2416347...
That's interesting TM I will pass this on cheers for that.
Hi yes it fuses ok just calls Sc code after approx 10 copies we think it may be sleeve, but thanks for the info.
Hi me thinks it could be the sleeve also as have not been to it but checked out parts manual, good shout cheers i will let him know Thanks.
Hi colleague of mine has MPC 305 with SC541. Has replaced 3 thermistors and thermopile, works for approx 10 pages then calls same code, cannot think of anything else on fuser that would cause this ,...
just been back and device has been running ok since last call!!!!. Taken advice though and stripped ITB again and removed rollers incl aluminium type and cleaned lubed on spec. Will let you know if...
Thanks for the replies, dev and pcu were boxed untouched brand new and stripped ITB to swap over trans rollers all rollers seemed to turn ok but will have another look on monday. Thanks
Getting Yellow dev and toner splodges on paper even while doing b/w copy, changed overdue life Y dev and pcu still the same, stripped ITB and swapped transfer rollers Y for K still the same fault is...
Good,call but don't use a vac on it as sometimes you can damage TD sensor, new dev unit in that case as TD not available on it's own.
If you put new Dev in need to check dev fill set are all 1111 also dev initialize set 1111, if any other numbers other than 1 need to re initialize that dev, not supposed to but may get you out of a...
Had continues SC995 turned out to be faulty NVRAM, if you cant back it up you could try initiliaze but only after exhausted all other avenues
Just an update seems to be stable now after fitting EGB so probs old fans have caused issues with EGB. Thanks
Thanks for the reply's people given me food for thought, as all fans replaced will try engine board route and let you know what happened cheers.
Cheers will do going back monday with boards just in case though.
Hi Ricoh SP5200 with SC530, SC532. SC534 in succession ie 1 second apart on error list have changed all fans works for a bit then random SC534 or SC530 done alot of prints 950K. Thinking psu or...
Cheers slimslob,, in this case it has 3 actuators or size detect sensors but not faulty in this situation thanks will log that though.
Well if it works with rear door open I would say that door switch must be shorted or something, As far as getting the paper to exit that way you would have to come with a way of triggering the exit...
Ditto this.
Would doubt you can overide exit switch for safety purposes as close to fuser etc. move the device