Thanks I will give that a try
Type: Posts; User: Sharptech56
Thanks I will give that a try
I have a Bizhub 458e all of the drawers either are hard to or won't open.I replaced the lock holder plates removed the springs on the drawer rear side and checked the lock release. When open the...
I have a 3515ac that double counts ltr size thick 1,2,3 paper from bypass after selecting proper size and type I went to 08-6014 set to 0 no change
anyone else seen this already updated firmware to...
I replaced the MFPB board and reloaded firmware and so far so good we will see if it is a long term fix
This machine was working fine for 67000 copies before problem occurred and I checked the set screw on the pulley and motor
It might have something to do with shading maybe
When the problem first occurred I followed the procedure in the service manual check home position sensor in service mode, state confirmation ( actually replaced it twice ) also replaced scan motor,...
Hi All
I have a 454e with a c-6102 error code the scanner once in home position just shakes until it codes out. If I take it out of home it slowly returns and starts shaking like it is ignoring the...
Thanks for the advice. That makes sense, I will investigate further along those lines.
Sorry 6506ac and the error is listed in the service manual as 4011 printer error print job cancellation
Customer claims the error occurs when sending a print job from a variety of applications...
Hj Guys
I have a EStudio 6505AC and 4505AC at a school brand new and they both wjll code out 4011 quite alot. Toshiba had me do a firmware upgrade but, it didn't help.
Anyone seen this?
Hi All
Has anyone sucessfully replaced the fuser motor in a MPS5502 Oki MFP. I've been at it for a couple days and the thing just won't come out.
Oki suggested replacing motor after 3 tries at...
Finally got back to account checked DV unit toner chute and cleaned toner clutch . I then checked the toner itself and found it did not really turn well by hand
so I must of shooked,banged,and...
All good suggestions guess I got some work to do I will post what I find............
Hello all,
I have a MX-M503n with 300K on it and it staryed clicking , saying "toner replenishment" and eventually F2-64 already tried new toner . Ordering toner clutch am I missing something ?
Hi All
I have got a strange one.A MX-M623N 800K copies on it a MX-FN15 finisher down FSMJ( jam no paper all sensors check out) on display look it up FSHS sensor on the staple unit Not turning on...
Well ,if you have to replace the lever be prepared to take out the laser unit
Thanks for the reply and that is what I thought . So I re seated the HVT and slid all process units in and out. My next move is firmware then PRCB.
I had a 5102 trouble code indication that the M1 motor was bad . So, I replaced the motor
then it said to install the process unit . I reseated all process units and checked the HVT board for ...
Has anyone ever had to replace the paper out lever in tray one on a c3350.
It looks very difficult if possible and the service manual has no procedure
Hello all
Anyone have experience with KM FS-533 finisher (add staples) message intermittently and or staples missing the pages and collecting on top of the cartridge.
Well it looks like a bent transfer belt frame and running belt rotation sims with the front panel off causes the black drum to conduct and coat the drum because of light sneaking in.
Thanks! besides the error we are also getting large splotches of Black toner and smaller splotches of colored toner on the transfer belt when we try to run the( KcsNo31.zip )calibration sheet ....
With new belt installed we re-leveled and tested the belt still meanders to the right (E-0722 error every time) after adjusting tension and inspecting belt frame getting Konica rep involved to...
We successfully installed the new transfer belt yesterday gonna let it settle over the weekend and re-level it before power up and calibration
Thanks that helps I think that if we get the transfer belt in ok we will let it sit overnight and check the level the next day. I am just not sure why the belt ripped in the first place.