Search:

Type: Posts; User: Konicatech

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    635

    Re: Dash Marks cs 5053

    Sorry to revive an old thread, but what was the fix for this? Seeing it happen more and more...
  2. Replies
    19
    Views
    1,811

    I series premature fuser failure

    I have changed countless fusing units on these machines (c250i and c300i) all because the toner was rubbing off the page.


    Anyone else experiencing this? If so do you have a fix rather than...
  3. I Series Dev Unit Convert from Black to Colour

    Know people have had success converting K Dev units to colour dev units on the 4 and 8 series machines, has anyone successfully done it on the I Series?
  4. Replies
    14
    Views
    1,396

    [Misc] Re: Is this normal for KM C258?

    Ok so if cyan and magenta are showing the pattern then that narrows it down, could be needing new C & M drums or could be needing C & M dev units, or could be both!

    What toner is the machine...
  5. Replies
    1
    Views
    2,713

    Re: Part Number Konica C300i SSD

    AA2JM72Q00
  6. Replies
    9
    Views
    577

    Re: C250i taking 6 mins to come to ready.

    I remember installing a lot of these machines when they were first released and thinking they took an age to boot up properly.

    Update the firmware and I think you will see some improvement - ...
  7. Re: New Ecosys PA4500x not waking up from sleep mode

    Make sure the print drivers are using the IP Address to print to the machine and not WSD
  8. Replies
    9
    Views
    1,786

    [Electrical] Re: C250i Won't Power On

    Had same issue recently, was the CPU board.
  9. Re: Konica Minolta C7000 dark lines on all colors. Replaced transfer belt

    Assuming you don't do much work on these machines, but yes the dev unit opens up (that's how you empty it to replace the developer) You should check the roller and see if something is stuck on it,...
  10. [Misc] Re: Print in B&W when out of color toner and won't print from PC

    Had this problem myself, and unchecking the 'SNMP Status Enabled' option allowed me to get the machine printing again until the colour toner arrived.

    will work as long as on the MFD the option...
  11. Replies
    7
    Views
    750

    Re: Word ignoring driver settings

    Thank you all, I will try out the methods listed :)
  12. Replies
    7
    Views
    750

    Word ignoring driver settings

    Scenario - customer receives documents to print, opens them in word and tries to print them using the driver settings but Microsoft word prints them using the page setup and things print from the...
  13. i Series - Change admin password from web browser?

    Does anyone know if possible to change the admin password from the web interface rather than doing it from the display panel?

    Thanks
  14. Re: Papercut stuck in KM trying to install printix

    Open API Tool/Manager will remove it provided the tool is configured properly.

    Otherwise set the device up on Papercut and remove it from there.
  15. [Misc] Re: Use a generic HID card reader for authentication

    Sounds like a lot of hassle, can you not just get the correct card reader from KM? We usually use ELATEC or Ysoft readers and get the LDD from KM..
  16. Re: Kyocera M6235cidn black toner empty after 2 new ones still says toner empty

    I have had this more times than I care to remember, do the following:

    1. Take the chip off the toner cartridge

    2. Install the toner and let the machine get to ready state

    3. Take the toner...
  17. Replies
    18
    Views
    1,283

    [Misc] Re: Strange Issue with a C224

    I think you might be out of your depth here, if you start swapping boards around as said above you might end up with 2 broken machines.

    They are not on firmware version 7, they are on function...
  18. Replies
    18
    Views
    1,283

    [Misc] Re: Strange Issue with a C224

    Fair, they are good machines anyway and consumable prices are low if you buy drum rebuild kits etc.

    Re: things turning when you are not using the machine I wouldn't worry about it if it was me :)
  19. Replies
    18
    Views
    1,283

    [Misc] Re: Strange Issue with a C224

    What monthly volume is going through the machines?

    Also a C224 is not a newer machine, its 11 years old.
  20. Replies
    18
    Views
    1,283

    [Misc] Re: Strange Issue with a C224

    Sounds like the 1 that "the drums are not turning" is behaving as it should be and the other machine is not.

    Normal conditions are as follows:

    - After a period of inactivity the machine goes in...
  21. Replies
    8
    Views
    2,014

    Re: 3 or 4 series primary feed jamming

    On the 2 & 3 series we had a lot of problems with fusers causing jams but so far none of that on the 4 series

    For the tray 1/2/3/4 feed rollers, I find them to be pretty rubbish and usually fit a...
  22. Re: Taskalfa 2554ci Scanning pause before can touch start button.

    Guys,

    The solution has already been posted, update the firmware to latest and do the following:

    Function Settings > Prevent Miss-Sending Settings > Turn off the following: Destination Check...
  23. Replies
    12
    Views
    1,188

    Re: BH-C-xx8 series, noisy after market drums

    Yes has issues with the "noise" when rebuilding 8 series drums, its almost like an electrical sound.

    Thread on this below:

    Bizhub C258 high pitch whine when copying/printing
  24. Re: Taskalfa 2554ci Scanning pause before can touch start button.

    Hi

    Yes you are correct, latest firmware and then make those changes.
  25. Replies
    12
    Views
    4,322

    Re: Taskalfa 3252ci drum counter reset

    It cannot be done for this machine
Results 1 to 25 of 127
Page 1 of 6 1 2 3 4