Search:

Type: Posts; User: Fearless V K

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    6,561

    Re: Ricoh SP C811 Paper Mismatch error

    paper size info for print jobs is sent with the print job itself so I would guess the problem is in the print job paper size setup on the computer end.
  2. Replies
    8
    Views
    2,031

    Re: HP LJ 6015x

    Thanks for the replies.
    All drums have been original OEM new drums. Third drum tried last time worked but stopped working a few weeks later. Tried FOUR more brand new drums and none worked. HP said...
  3. Re: Ricoh Aficio 2060 error SC495 what else can it be

    Pull the rear recycling unit and clean the sensor and the toner which has hardened like cement inside the tubes
  4. Replies
    11
    Views
    2,084

    Re: mpc 3000 copy quality issues

    Just looks like some dust on the scanner mirrors to me. see that all the time. you said you cleaned the lamp and lens block but did you clean the mirrors?
  5. Replies
    11
    Views
    1,697

    Re: af1075 no display on the control panel

    More often that not, this is the classic symptom of a bad power supply.
  6. [Misc] Re: Aficio 1515mf goes into Sleep mode or power save while scanning

    I would try updating the power saver firmware to the latest and greatest as suggested. I have seen this on several machines and believe that it is a know issue to Ricoh as they have released new...
  7. Re: Ricoh 1013/Savin 2513 or MF161/Savin 816 "add toner" light & "Cleaning 100%" stay

    the spring loaded coupler which meshes with the end of the toner bottle at the rear of the machine may be stuck back into the machine frame.
  8. Replies
    3
    Views
    1,900

    Re: aficio 1035 sc395

    IOB?
  9. Replies
    27
    Views
    6,778

    Re: MP 2550 Mystery Jam

    I have also found on numerous occasions that the side and end fences are way to tight against the paper stack. this will cause the machine to not be able to properly lift the stack causing the tray...
  10. Replies
    4
    Views
    1,453

    Re: 3228c red light on fax button

    try turning POP reception protocol to 'off'
  11. Replies
    7
    Views
    992

    Re: Savin 4075 poor fusing

    check your fusing lamps for continuity. I have seen one of the 3 lamps go out and not pop a code. you should also be able to check the fuser temp in service mode to make sure it is actually where it...
  12. Replies
    8
    Views
    994

    [Jamming] Re: AF1075 JAMMING at Duplex unit

    My bad. you're right. was thinking a generation back. In that case, make sure the paper feed stations have not been contaminated with leaking developer from bad seals on the development unit, and...
  13. Replies
    9
    Views
    1,065

    Re: 1055 misfed at dupex?

    guaranteed this is caused by the paper feed unit clutches. it has nothing to do with the duplex unit. have seen it hundreds of times
  14. Replies
    8
    Views
    994

    [Jamming] Re: AF1075 JAMMING at Duplex unit

    bad paper feed unit clutches will cause this. seen it many times
  15. [Misc] Re: MPC 2050 Original size not recognized from glass

    May have something to do with the adf position sensor.
  16. Replies
    8
    Views
    2,031

    Re: HP LJ 6015x

    there is no strip
  17. Replies
    8
    Views
    2,031

    Re: HP LJ 6015x

    two new drum units are having the same problem. they are genuine HP. there is no obvious difference between the new drums and the old drum. the only thing I notice is a buildup of toner at the...
  18. Replies
    8
    Views
    2,031

    HP LJ 6015x

    new black drum unit and toner cartridge installed and black prints are blank. put old drum back in and its fine. tried second new drum unit and blank prints again. anyone seen this/have a solution?
  19. Replies
    24
    Views
    2,193

    [Jamming] check simple things like making sure the paper...

    check simple things like making sure the paper size setting thumbwheel in the paper tray is set correctly. does it jam on copies too or just prints?
  20. Replies
    5
    Views
    1,006

    adjust the scaling setting in the print driver.

    adjust the scaling setting in the print driver.
  21. Replies
    10
    Views
    1,455

    upload nvram to sd card. perform memory clear....

    upload nvram to sd card. perform memory clear. download nvram from sd card.
  22. Replies
    14
    Views
    2,745

    unplug the HDD if it has one. see if it works...

    unplug the HDD if it has one. see if it works then. if so... bad HDD
  23. Replies
    17
    Views
    2,375

    [CQ] You can leave the laser shutter out of the...

    You can leave the laser shutter out of the machine forever with no problems. If I have any issues with them I just trash them. Setting the SP mode to open the shutter more does not always work. You...
  24. make sure the lower OPC frame middle latch is...

    make sure the lower OPC frame middle latch is snapped in place (the little plastic tab in the middle of the lower frame, under the drum). if it isn't it will cause that problem.
  25. from output modes, turn on the main motor, then...

    from output modes, turn on the main motor, then energize the toner supply clutch while holding the stuck shaft tightly. this should spin the shaft housing until the d-shaft lines up with the d-shaped...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4