Search:

Type: Posts; User: The_Murph

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: ECOSYS P6035cdn with recurring CFFFF errors.

    That is consistent with what we saw as well, the concurrent fuser code. We found that it has to do with the fuser pressure motor malfunctioning. Replace fuser and problems cleared up. I don't have...
  2. Replies
    2
    Views
    2,381

    Re: M2535dn Grinding noise but still working

    QA G246 also refers to a cause of a noise. there is a ground screw on the machine right side that is too long from the factory. They shortened the screw in the QA.

    Good to know about the...
  3. Replies
    9
    Views
    3,932

    Re: FS-C8525 pale colour

    You may be dealing with dirty laser slit glass or even a dirty polygon mirror (2 lasers 1 for C,Y 1 for K,M) for the washed out prints. make sure to clean the MC's as well.
  4. Replies
    11
    Views
    2,834

    Re: Taskalpa 8002i

    Before swapping it out, I would check to ensure that the sep tension is set on the cass 3 mechanism.
  5. Replies
    12
    Views
    2,536

    Re: KM-4050 new drum with background

    When changing the drum on these, you MUST power the machine down prior to repalcement or the count will not clear.
  6. Replies
    7
    Views
    3,131

    Re: PF-740(B) tray 3 not lifting properly

    I would have a lift motor on the ready, the motor that is now on the cass 4 side is likely to have a broken tooth internally (common failure) and probably will fail again.
  7. Replies
    11
    Views
    2,834

    Re: Taskalpa 8002i

    Doesn't the 8002i have a sep tension adjustment for each source, similar to the 6052ci series machines? If so, it could be that the sep tension is slack. That would cause this in the new series... ...
  8. Replies
    8
    Views
    18,056

    Re: 720F error when scanning SMB

    I've been getting similar errors on both a 4002i as well as a couple M3550idn. Actually swapped a couple 3550idn models with 4002i due to "memory allocation errors" thinking that the limited memory...
  9. Replies
    9
    Views
    2,261

    [Misc] Re: 4100DN Printer Producing Steam

    Bizarre. What happens if you were to run a full ream through continuously? Does it "run out of steam" (so to speak)? Is it like a vapor cloud like when someone takes a pull off an e-cig? The...
  10. Replies
    9
    Views
    1,091

    Re: Blurred image

    How does the developed image look on the drum? Try a half self test to see... this will determine when the issue is happening.
  11. Replies
    2
    Views
    3,086

    [Error Code] Re: Frequent error 7410 on Kyocera FS-4020

    It's possible that the drum is shifting slightly from normal machine vibrations, causing flaky contact and thus errors. Is the "lock" tab being put back in place or is it missing? That keeps the...
  12. Replies
    9
    Views
    1,091

    Re: Blurred image

    What else have you tried? This may help keep helpful people from guessing what it may be after you've already tried something. Have you inspected the hex mirror on the laser unit? sometimes that...
  13. Replies
    5
    Views
    1,084

    Re: kyocera KM2560 prints 4 inches top of page

    Is it a sharp cutoff or is it somewhat inconsistent. Also is it tray specific? what about large sizes, does it print a specific sized area on 11x17? These answers may provide the necessary data to...
  14. Replies
    2
    Views
    1,981

    [Jamming] Re: kyocera TASKalfa 420i

    Your MPT issue is simply that the MPT is set for a paper size or media type that doesnt match the job sent. I would go into system menu->adjustments/maint and turn silent mode "on". This will help...
  15. [Jamming] Re: DF-710 Jam between the finisher and machine J 81

    What do you see when it jams, what have you tried? (the service manual has an entire section dedicated to how to determine and remedy jams)

    ... ugh ... J81 references the finisher entry sensor...
  16. Replies
    3
    Views
    1,955

    Re: Loading colour profiles

    The profiles can be downloaded from the manufacturer site, and the procedure is outlined in the service manual.
  17. Replies
    2
    Views
    1,279

    Re: Color Registration Issues

    What level firmware are you at and what have you tried up to this point?
  18. Replies
    5
    Views
    1,290

    Re: kyocera c2126 vs Mac computer

    Go into command center and disable airprint in the protocols section for MAC auto driver install, and disable WSD print to disable the auto population of uni-driver on PC.
  19. Replies
    5
    Views
    1,290

    Re: kyocera c2126 vs Mac computer

    If printing from an Adobe product, There is a default enabled box in advanced settings entitled "JPEG 3000" it clearly states that the driver will use maximum allowed dpi to process the job. ...
  20. Replies
    28
    Views
    58,613

    [Misc] Re: Secret Service Code on Kyocera

    I think the usefulness of the clips is that it provides a redundant circuit to ensure proper connectivity between pwb's. Use many clips, that will ensure that the reset menu is displayed.

    good...
  21. [Misc] Re: Kyocera 306ci Copying 8.5 x 11 size onto legal paper

    The 306 is the low-rent model in this engine line. Things to keep in mind are that this uses the lowest quality DP unit and therefore the paper detection sensors may be cheaper. You can set up a...
  22. Replies
    2
    Views
    6,775

    [Jamming] Re: Kyocera Ecosys M3550idn

    I agree with Spark about the heat. I have a goofy question, how is the flag bent? What I mean is, is it bent as if it were heated and bent or does it have a more "abrupt" bend to it? depending on...
  23. Replies
    20
    Views
    6,975

    Re: Print Quality Taskalfa 3050CI

    Thats quite the markup. I wish I could get away with that ... I'd get a competitor out and tell them you were quoted 300, I bet you get it for a little less than that.
  24. Replies
    10
    Views
    23,429

    Re: FS-1128 displays 'replace process unit'

    Also, to piggyback on this thought of resetting counts, you CAN empty the waste out, however if you wait until it is full, the cleaning blade will be fouled and you have to replace it anyways. Its...
  25. [Misc] Re: MP C4503 is on please wait loop and not able to enter SP

    Haha ... low tech rules!
Results 1 to 25 of 101
Page 1 of 5 1 2 3 4