That is consistent with what we saw as well, the concurrent fuser code. We found that it has to do with the fuser pressure motor malfunctioning. Replace fuser and problems cleared up. I don't have...
Type: Posts; User: The_Murph
That is consistent with what we saw as well, the concurrent fuser code. We found that it has to do with the fuser pressure motor malfunctioning. Replace fuser and problems cleared up. I don't have...
QA G246 also refers to a cause of a noise. there is a ground screw on the machine right side that is too long from the factory. They shortened the screw in the QA.
Good to know about the...
You may be dealing with dirty laser slit glass or even a dirty polygon mirror (2 lasers 1 for C,Y 1 for K,M) for the washed out prints. make sure to clean the MC's as well.
Before swapping it out, I would check to ensure that the sep tension is set on the cass 3 mechanism.
When changing the drum on these, you MUST power the machine down prior to repalcement or the count will not clear.
I would have a lift motor on the ready, the motor that is now on the cass 4 side is likely to have a broken tooth internally (common failure) and probably will fail again.
Doesn't the 8002i have a sep tension adjustment for each source, similar to the 6052ci series machines? If so, it could be that the sep tension is slack. That would cause this in the new series... ...
I've been getting similar errors on both a 4002i as well as a couple M3550idn. Actually swapped a couple 3550idn models with 4002i due to "memory allocation errors" thinking that the limited memory...
Bizarre. What happens if you were to run a full ream through continuously? Does it "run out of steam" (so to speak)? Is it like a vapor cloud like when someone takes a pull off an e-cig? The...
How does the developed image look on the drum? Try a half self test to see... this will determine when the issue is happening.
It's possible that the drum is shifting slightly from normal machine vibrations, causing flaky contact and thus errors. Is the "lock" tab being put back in place or is it missing? That keeps the...
What else have you tried? This may help keep helpful people from guessing what it may be after you've already tried something. Have you inspected the hex mirror on the laser unit? sometimes that...
Is it a sharp cutoff or is it somewhat inconsistent. Also is it tray specific? what about large sizes, does it print a specific sized area on 11x17? These answers may provide the necessary data to...
Your MPT issue is simply that the MPT is set for a paper size or media type that doesnt match the job sent. I would go into system menu->adjustments/maint and turn silent mode "on". This will help...
What do you see when it jams, what have you tried? (the service manual has an entire section dedicated to how to determine and remedy jams)
... ugh ... J81 references the finisher entry sensor...
The profiles can be downloaded from the manufacturer site, and the procedure is outlined in the service manual.
What level firmware are you at and what have you tried up to this point?
Go into command center and disable airprint in the protocols section for MAC auto driver install, and disable WSD print to disable the auto population of uni-driver on PC.
If printing from an Adobe product, There is a default enabled box in advanced settings entitled "JPEG 3000" it clearly states that the driver will use maximum allowed dpi to process the job. ...
I think the usefulness of the clips is that it provides a redundant circuit to ensure proper connectivity between pwb's. Use many clips, that will ensure that the reset menu is displayed.
good...
The 306 is the low-rent model in this engine line. Things to keep in mind are that this uses the lowest quality DP unit and therefore the paper detection sensors may be cheaper. You can set up a...
I agree with Spark about the heat. I have a goofy question, how is the flag bent? What I mean is, is it bent as if it were heated and bent or does it have a more "abrupt" bend to it? depending on...
Thats quite the markup. I wish I could get away with that ... I'd get a competitor out and tell them you were quoted 300, I bet you get it for a little less than that.
Also, to piggyback on this thought of resetting counts, you CAN empty the waste out, however if you wait until it is full, the cleaning blade will be fouled and you have to replace it anyways. Its...
Haha ... low tech rules!