Sorry for not providing the necessary info. I attached the 22-6 print you suggested.
When I replaced the drum I also replaced the cleaning blade and the developer (only the black one).
44884
...
Type: Posts; User: jonathan3205
Sorry for not providing the necessary info. I attached the 22-6 print you suggested.
When I replaced the drum I also replaced the cleaning blade and the developer (only the black one).
44884
...
Hi i'm here requesting your help once again.
I have a Sharp MX-5001 that is leaving a black strike on the middle of the pages. One month ago the printer was leaving the same strikes on the prints...
Hi, I have a MX5001N, and need to replace the TN cooling fan part number FANP0112FCPZ to solve L4-57 error, but I can't find it anywhere. The label says nidec d04r-24th-47b. Do you have any idea...
Hi I have a MX5001-N and I'm getting the L4-57 fan error. I used simulation mode to check the fans and effectively the right PCSFM2 fan is not working. I've been looking through the service manual...
Wow, thank you very much. This solved the issue, now I just have wait untill the replacement arrives.
Thanks for your help
Hi, I have an MX-5001N Showing the error C4-02. I already order the replacement part, but it wont arrive till the next week. The manual says that you can temporally override this error by changing...
Replacing the whole fuser was the last thing I wanted to do, but I guess I have no other choice. But I am amazed by the fact that this fuser only lasted 50k pages.
Just one last thing I would like...
If you are talking about the upper separation pawl I didn’t replace them because the service manual says that you should replace them after 300k pages and this fuser unit only have like 50k pages (I...
Hi, I have a MX5001N. 7 days ago we were printing and suddenly when printing a color image a page got stuck on the fuser, I pulled the sheet and a piece of the upper heat roller came out with the...
How likely do you think this has happened? 50% or am I 100% screwed? How do I know it its damaged?
The parts should arrive on Monday, but I have another question and I hope you can help me with it.
Today I take out the developer unit to clean it from the old developer, the unit was almost...
Thanks, as soon as the parts arrive I will do it and let you know what happened.
Hi I’m about to replace the black developer and the drum unit for the black color on my MX-5001N. I was reading the manual and it says you have to run some sims after replacing these components but I...
So I better stay away from it? Right now what I need the most it is to adjust the 1 CM offset when using the ADF, but I had no luck.
UPDATE. SOLVED at least the ADF problem the option was 50-12 B...
Thanks for the info about the bolt.
I have been trying to adjust the 1 cm void using SIM 50-12 and 50-6 but I can't can't figure it out. Am I using the correct sim? Or should I use 50-28?
Update, you were right it was the SPED sensor now its working again BUT now the copies and scans using the ADF have the bottom cut or to be more precise are moved down for about 1 CM. Here are the...
There is no jam code, it only says "a misfeed has occurred" but the pages that pass trough the adf are correctly sent to the pc or copied. Tomorrow I'll check the sensor you mention.
Thank you so...
Thanks for you reply, I did what you said and checked all the sensor from the ADF, the one sending this message was SCOV because the plastic that pushes the sensor flag was broken but using a little...
HELP I FUCKED UP. Please Help guys I dropped the DSPF unit. I read the service manual but I read the wrong part and proceed to remove the DSPF unit but I didn't know it was so heave and I drop it....
Hi again I have a problem with my MX-5001N. When I make a copy using the document glass, the copy shows a black line on the right edge of the page as well on the top right corner. When using the ADF...
Ok guys today I received the new OEM toner and the issue got solved immediately. Guess I will be sticking to OEM toner until I find a compatible brand that works well on this machine, maybe katun or...
The maintenance was performed by a technician from the company who sold us the machine, so I don’t know if he did that procedure or not and since this company simply vanished from the earth without...
What should I try then? Change the developer or the toner?
As a side note recently switched from a brand I do not remeber the name, but was printing fine and then started to use toner BlackStar...
Here is the sky shot
34879
Yeah I wish I could afford it, but here in México It is super expensive and difficult to find it. :(