Machine has 20k in total. First toners inside (OEM of course. Paper came out with clean picture but toner is smearing under the fingers (not fixed).
I raise the fixing temperature in service mode 10...
Type: Posts; User: REGSIS
Machine has 20k in total. First toners inside (OEM of course. Paper came out with clean picture but toner is smearing under the fingers (not fixed).
I raise the fixing temperature in service mode 10...
Dowload NG has nothing to do with FW itself.
Usually a CPU board is corrupted/bad.
It should be replaced sooner or later.
I've installed Q9 on one macchine 2 days ago without any problems.
But...
I can confirm this. I did this only couple of times, but it works. It is recommended to stabilaze the image and run gradation adjustment. There should be no issues because TCR sensor is reading the...
Diagnostic tool should piont you to the faulty part (CPU board or SSD board). Replace it and update FW (select correct machine model).
In my case it was a CPU board.
If the machine was OFF for a long period of time this message is shown. In this case you have a chance for recovering.
You must have installed twain driver for this model (you can prepare it with...
If that driver is on KM site then KM should ensure it work without issues.
It's KM fault definetly, not customers at all.
But customers and especially ITs should trust service technicians when they...
Its function is to release and stop rotation of developing unit at specific time.
Sponge on solenoid acts as isolator, if it's worn timing is wrong.
Nothing is broken, solenoid works, all you have...
Recenty I had an issue with universal PCL driver. Print with that driver came out OK but it blocked next job in queue.
IT guy reinstalled PC and didn't pay attention and installed 1st one offered on...
Bizhub 306i should be bizhub 306 with new control board and operation panel.
Developer, drum, toner and 90% of parts should be the same as in bizhub 306.
When you change developer, first you have...
Machine always stops after 3rd page when printing or copying more than two pages.
One page and two pages are printed OK, on both single and double sided print.
If you set three or more pages it...
Hi everyone!
Few of these printers at customer's sites print one page immediately, but the other pages are printed after delay of 1-2 minutes.
There's no error on printer, no error in print queue...
If you get solid color output (or even thick vertival bar) of one color that means there's no grid charge apllied on drum or developing charge applied on magnet roller or even both together.
Toner...
Did you swap printer control board (right to the MFP board)? It might be dead also!
Sensor monitor
59538
That info is the answer to my question.
Thank you!
You are almost right, but not completely.
FS-536 is finisher for all B&W 8 series, but not all color models.
C658, C558, C458 - FS-536
C368, C308, C258 - FS-534
Similar aproach is applied to...
Hope you got my PM
PS40 (1st duplex sensor) is activated.
Possible causes: piece of paper on actuator, broken actuator, spring out of place, faulty sensor.
For location of PS40, see the...
Does FS-536(SD) work on bizhub C368 series?
I have them mounted on C558, but asking just in case.
Those are pretty serious machines you have to maintain.
It is allways a good thing to have spare parts. They will be replaced sooner or later.
For the fact that you are not a technician, I suggest...
You can, but you will probably get dirty background after a while (When old toner comes into dev unit).
If you intend to stick with TN211 then DV116 is maybe more compatible with dv310 than dv414....
What I will do when TN-211 became empty is to replace it with TN-217/TN-414 but before that I will empty dev unit and put DV-411. Also remove toner hopper and vacuum old toner. An old (empty) TN-211...
I think that all drum cylinders are the same and with the same yield. Only the chip and some plastics are different.
I have seen some DR313K drums lasts up to 180k which is the yield of long life...
I didn't try, but I assume that you can swap drum, blade, charging roller and charger cleaner from new DR-313K to housing of DR-316K/DR-316YMC. Parts should fit, and are definetly cheaper.
I think so.
But also I also think that it's not the same part number for CL8 as in 4 series. Check parts manual.
Customer reported after 50k when the printed a job with a solid purple background.
It was present at all colours; on K the most.
Bandings were not as thick as yours.
I took a K drum from...