Pick a window!! (Preferably from a high floor)
Push the device out of choosen window
Watch and cheer as the machine hits the flooR!!!!
Type: Posts; User: Batman1976
Pick a window!! (Preferably from a high floor)
Push the device out of choosen window
Watch and cheer as the machine hits the flooR!!!!
Quick update guys....
this turned out to be the carriage unit. Replaced complete unit and warranty part.
Thanks
Batman
Hi Chaps,
59638
Update on this one. On inspection, Transfer Bias contact spring was damaged and mis-shaped causing faint PCQ and obstructing transfer belt stopping it finding Home position. ...
The toner amount remaining/shown in the display is calculated through the pixel data and the number of the toner bottle rotations..
And, 20% and End are judged by the sensor.
The phenomenon...
Hi Chaps,
Anyone ever had an MPC307/407 with a transfer belt unit making a noise and producing faint prints?
Transfer belt unit including cleaning unit have been replaced and fault persists. ...
Hi Chaps,
I also experience the same issue on our fleet of MPC307/407/IM300/400 devices. You can try adjusting the toner near end threshold via SP mode this will give you a bit more notice at...
No movement of scanner at power on, no lamp on either. Scanner carriage moves freely by hand, no obstructions. ADF disconnected gives same error.
Hey Chaps,
Have an IMC3500 with Sc144 on display, Reseated scanner ribbon cables but no joy. Manual points towards BICU or Scanner carriage assembly replacement. Before I start ordering...
Yep, Done that have the video but machine doesn't do when attending site.
Hi all,
Has anyone had any issues of Proc5300 with intermittent fan noise? We have run fans in output mode and cannot pin point a noise.
Does seem to be very intermittent, as usual customer...
Hi all,
Bit of a strange one. We have replaced a Ricoh IM350f like for like (same model). The device is connected to one pc via USB. The old IM350 printed fine via USB. The new IM350 however...
Ask clients IT support to empty or clear up the destination email address inbox
I have had similar issues with send meter app failing using Office365 lately, Any Update on this would be gratefully received?
Check the Mylars on the shift exit rollers. Remove them!!!
Hi Chaps,
Few options to look at:
Toner end threshold levels on Ricoh devices can be adjusted within SP mode to allow for longer/shorter notification times.
If a client has multiple devices...
Try formatting the HDD. This should remove any 3rd party software previously installed.
Failing that look at replacing HDD and/of Controller PCB.
Batman1976
Known issue.
New boards have been modified to stop fuse blowing, must be replaced a s a pair.
Batman1976
Hi Steve,
The exit rollers of the device should be changed when installing the bridge unit along with a small plastic guide. Have a look in Bridge Unit parts manual for correct exit rollers and...
11035841 (connector:28w0r-rfc-egd(lf)(sn))
11035840 (connector:rfcp-28w0-e)
11035760 (connector:36w0r-rfc-egd(lf)(sn))
11035758 (connector:rfcp-36w0-e)
Hi Chaos,
This turned out to be a slighty broken blue connector block on right rear side of the main draw unit. This was causing a loose connection of the cable and resulting in intermitten Jams...
Yeah, so with these new fiery devices you need to register for the EFI Fiery Sales Portal (24-48hrs). You then need to download the Fiery INSTALL BUILDER. The fiery system software is then...
Hi Chaps,
I have an ongoing issue with a E25c fiery on a IMC device. It keeps dropping off and needs a reboot. All services packs and patch updates have been applied. Also machine firmware is...
All original OEM Parts replaced. Mainly A4 from any tray.
In saying this I've just run over 500 sheets through and ZERO jams. I'm gonna run with it and keep an eye on Jam history.
Hi Chaps,
We have an MPC6503 with intermittent jams at fuser exit/inverter sensor - Jam code 025.
Fuser has been rebuilt with all parts replaced. Sensors cleaned etc etc. Paper seems to stop...
Yes, E-24b. Smaller fiery with LED display at rear.
I'm using an external disk drive via my laptop as the USB Tool will not work when downloaded from My-Ricoh (Suggests a virus is detected).