Yes it is old. Sorry i lose my account from ricoh now 3 years ago when i start to work with toshiba, hp, lexmark,brother.
gkalman
Type: Posts; User: gkalman2004
Yes it is old. Sorry i lose my account from ricoh now 3 years ago when i start to work with toshiba, hp, lexmark,brother.
gkalman
Yes i remove it, but i not check the pre-registration sensor flag because i did not know she had also there one .
Thank you, i will check tomorow also this tip.
Hi everybody
I know it is older post but i have the same issue 0A01 with one almost new IR2530i, i changed all the sensors from the pick up assembly and i change the clutch's beetween them...
For what type of ADF? Both firmware version have 800MB
4CCD – Yellow
3CCD - Red
Find under the glas the Yellow or Red mark on the right corner or on the CCD.
If you write the wrong firmware you...
The service manual size is 51.9MB i have it if still need it someone
SERVICE MANUAL
MULTIFUNCTIONAL DIGITAL SYSTEMS
e-STUDIO206L/256/306/356/456/506
e-STUDIO306S/356S/456S...
Hi
I have the file if you need it get it form here https://mega.nz/#!vol1zTwb!CZLpkRYvHTCGEAIflJPt4fTNIcqySSuTmwK02nlEEVs
Hi everybody
I have a Lexmark MFP with 201.00 error. I changed all the transfer roll asembly, registration clutch and printer engine card
If i take out the transfer roller the mfp print out white...
it is not wrong machine it is wrong country...
The same machine can be used in china, us, ue etc..
Check with firewall and antivirus disabled.
Also check if the share is accessible from other pc.
A267-2803 isn't it Paper End Feeler? ( Actuator for Paper End Sensor)
Sensor is AW02 0141 Photointerruptor at least usualy ricoh note sensors with AW
The speed will be no problem the machine will not slows down, but the power it is and the motor will work less than the original because long run printing will produce heating and the heating will...
For the same MP9002 you can get
D131 5122 PCB: BCU: 60-75CPM:
D133 5122 PCB: BCU: 90CPM:
Regard's
" Or one of those silly marketing plots?"
The speed difference is from the controller not the motor
The motor will work well, maybe the lifetime will be shorter but nothing disturbing
Controller or nvram error, usualy the controller is faulty and the nvram is ok.
If you have a working machine take out the controller with the nvram and test on the faulty one.
If you change the...
Hi
I fix an old sr3000 booklet finisher and i also repair an incomplete puncher (it was defect with missing electronic pcb)
I order everything also the electronic pcb and i make it to work.
The...
Thank's
The cleaning blade was replaced already and i don't want to put new drum until i don't find why i have toner powder everywhere i will change first
AA15 0671 Shield - Collection Coil and...
Hi
I have an old machine with printing problem i changed the development unit, the developer, id-sensor, charge roller, cleaning blade, secondary charge roller cleaning blade, i do id senzor init,...
Replace PCU:C or clean charge roller
Print the network configuration from the machine from tolls-> system settings -> interface setting -> print list
Take a laptop and a cable and conect with a laptop directly after you change the ip...
yes i use scan to folder on MP C2500/2800/3300
for MP C2500 it is needed a custom firmware for the 2800/3300 the lastest firmware will work.
Just create a new user ex: "scan" with a password,...
For mp c2500 it is a customized firmware for windows 10 smb scaning.
I used it with succes more times.
But for MP C2800 i use the lastest firmware and it work with windows 10.
Some setup for...
Hi
I fixed the machine j029 it was paper stuck in the space between finisher and removed incomplectly by the user.
The machine in case of paper misfeed "D" instruct the user to open the finisher...
Hi
I have a problem with a new mp c8002 first with the developer motor sc326-00 what i fixed but after i receive paper misfeed what i also fixed with sp 1134 -001
And the machine print simple...
I have the same issue almost, i also change the IPU the lasser unit and nothing worked until in my case i changed the harness .
I can't tell if this will be also in this case but changing the cable...
Double check the part numbers on my order one cable the sync was with different harness.