Search:

Hello, everyone,
and thank you very much. Can the defective solenoid also lead to errors when printing from cartridges 1, 3 and 4? This is where the same problem arises. The fuser has only run...

Hello, everyone,
Unfortunately, the error now occurs again out of the blue. Paper jam error 0113 and sensor UN53 are currently displayed. I'm slowly running out of ideas. Can this really be caused...

Hello,


unfortunately, as expected, the error persists after we before. As suggested, I will now exchange the corresponding unit with sensors and coils. Maybe the error will move with you.
...

Since you can only test this with several hundred pages and correspondingly special paper, I can only test it next week. Then I can also give feedback.

Thanks in advance

Hello everyone,
the strange thing is that it works with another IRC5030 machine without any problems. This also shows corresponding values ​​in the I/O menu when the switches are touched. After...

Hello, everyone,
many thanks for the help. After changing the Cassette Feeder PCB, the values ​​in the I/O menu are still the same as before, but the device seems to be working now. Nevertheless,...

In the meantime i have cleaned all sensors and removed the first and second cassette pickup unit. I have removed the cables from the whole units. In Service Menu under I/O P-Sensors DCON on P021 you...

Here are some Pictures from the paper jam. Maybe this will help:
53608
Paper before registration

53609
53614
Jam Description in Service Menu

53610
Sensor PS56

Hello, everyone,
I have a Canon IR5235 here that generally causes paper jams with code 0202 and sensor PS56 with thicker paper from all cassettes.
The paper remains approximately 4mm in front of...

I tested the following Units:
-Black Drum (with a used one from another machine)
-secondary Transfer Roller
-BIAS contacts
-Laser Unit

I basically advise my customers honestly do not sell them...

Can it be the Primary Transfer Roller for Black ?

I'm not currently at the machine to change the laser units.I have checked the BIAS contact and it‘s ok.

the drums can not be exchanged. they are not mechanically compatible. I'm just wondering that the result on heavy paper is perfectly fine. Is there a way to re-evaluate the developer? this is also...

Can it possibly be at the black drum? The drum was only replaced before 3000 pages. Can still have a problem. This may be places that are defective, so that this does not properly recharge. The...

For both papers it looks the same on the ITB. However, on the heavier paper the expression is perfect. In the case of plain paper, the print is also opaque when copying with an open lid. There's...

On thick paper (250g) black is very goog. No error.

I have checked the dust blocking glass and cleaned them. The image on the transfer is good and had no errors. Condition of the primary transfer roller is 43 % (219608 pages). Condition of secondary...

The page is PG5 with Dens-K 255. The area is constant and not moving. I mean the light area in the middle. This is only in black. All over colors have no problems. I use the paper this is inserted...

Hello everybody,
I have here a Canon IR C5030. This has a very funny problem. He has received a new Drum BK and a new developer unit about 3,000 pages ago. All the prints were still correct from...

Hello,
thank you for the tip. I will test this in another machine with the old Developer.

Hello together,
with me is about an IR C5051. This goes after 5 minutes into the 0W standby. So far everything is good. Now the printer sproradically again wakes up and drives completely up and goes...

I have replaced the development unit Black and the error now disappears.

Thanks for the reply, I will replace the black developer unit with an new one and see then.

The Developer have 45 percent life.

Hello everybody,
The error is back. So slow really annoying. Meanwhile I have changed:
-the black drum
-ITB
-Fixing Unit

The error is not now on the entire page, but now affects only single...