Search:

Type: Posts; User: mrsoul

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    32,682

    Hi fren, have you settle the problem, this is...

    Hi fren, have you settle the problem, this is very common problem which faced on the field, pls check the tab at the left top side of the drum unit, is to actuate the laser shutter, another problem...
  2. Replies
    5
    Views
    2,166

    Hi, please take note when replace any main...

    Hi, please take note when replace any main controller must make sure use back the counter pcb, or elase you will face this error code, new counter pcb only can be replace when the machine run up to...
  3. Replies
    13
    Views
    2,091

    Have you replace the spacer roller, as spacer...

    Have you replace the spacer roller, as spacer roller may deformed after machine run above 250k.
  4. Replies
    4
    Views
    3,768

    Fren, most properly cause by the power supply...

    Fren, most properly cause by the power supply pcb, or you can try to re solder the contact point
  5. Replies
    10
    Views
    5,489

    hi, you can try to clear the machine by using...

    hi, you can try to clear the machine by using service mode, Additional Function>ID>scroll to #12 CLEAR>start>scroll to CLEAR All>start, off the machine and on again, if can't then another method is...
  6. Replies
    10
    Views
    11,188

    we have face this problems few times, you can try...

    we have face this problems few times, you can try to reconnect the flat cable or some connecter at IP Board there, if can't solve then no choice have to replace IP board
  7. Thread: IR1600 e000

    by mrsoul
    Replies
    1
    Views
    1,473

    You can clear it by going to service mode,...

    You can clear it by going to service mode, additional function > ID, scroll to #7 PRINTER > #4 PRINTER RESET > YES >*. OFF the machine and ON it again, if same problem then check the heater lamp.
  8. Replies
    1
    Views
    1,626

    This is commen error code, is cause by a stepping...

    This is commen error code, is cause by a stepping motor gear broken, just replace FK2-0144 will solve your problem
  9. Replies
    2
    Views
    2,057

    Thanks for your advise, we never use compact...

    Thanks for your advise, we never use compact toner, not reliable and a lot of problem
  10. Replies
    2
    Views
    2,057

    iR2270 error E024-0001

    Good day all, please give some idea how to solve this problem, toner sensor changed but still appear this problem after some copies
  11. Thread: IR2016 Fuser

    by mrsoul
    Replies
    2
    Views
    1,773

    Fren, you can just replace the fixing film ass'y...

    Fren, you can just replace the fixing film ass'y FM2-3353, if only the film torne.
  12. Replies
    9
    Views
    1,513

    May I ask, is this machine high usage, please...

    May I ask, is this machine high usage, please check the flag, sensor level, it will worn off and become shorter, (FF6-2363 New Parts No. FB6-3398). new parts have added with a metal plate, that can't...
  13. Replies
    31
    Views
    3,493

    you can try go to service mode to increase the...

    you can try go to service mode to increase the fixing temperature, it may help poor fixing.
    Copier>Option>Body>Tempcon2.
    Default is 0-Off, 1: -10degC, 2: -6degC, 3: -3degC, 4: +3degC, 5: +6degC,...
  14. Replies
    31
    Views
    12,413

    you can replace this 2 modification parts to...

    you can replace this 2 modification parts to improve the paper flow FM3-1296 Right Lower Door ass'y and FM3-1297 Right Inner Door ass'y. I hv try is good
  15. Replies
    13
    Views
    18,332

    Hi fren, you can go to service mode, function,...

    Hi fren, you can go to service mode, function, clear, pwd-clear. to clear all password
  16. Thread: IR1600 E000

    by mrsoul
    Replies
    3
    Views
    3,760

    hi, this E000 is very comman fault, you can try...

    hi, this E000 is very comman fault, you can try to re-solder the power supply PCB, some of the components already dry joint. good luck
  17. Replies
    3
    Views
    1,630

    we do face this problem very often, is due to...

    we do face this problem very often, is due to composite power supply, normally is caused by dry joint of the pcb ass'y.
  18. Replies
    2
    Views
    820

    iR2200 Error 220-0001

    dear friend, I have face this problems few cases, the error code shown is not caused by lamp inverter, actual problem is power supply 24v output not constant, can any experts advice how to repair...
Results 1 to 18 of 18