Search:

Type: Posts; User: tcs04

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    15
    Views
    2,600

    Re: MP6500 fading to grey

    No! Don't!
    That Will just scratch the roller!
    Fold a sheet of paper into 8. Using the shortest edge, scrape it against the roller (if it's black!). Vacuum the roller to get rid of the debris. If...
  2. Replies
    7
    Views
    1,241

    Re: c2003 uneven image density with all colors

    Condensation?? (After shipping?)
    ALSO
    silly (?) Question, have you shipped the machine full of paper? Is it damp?
    Change the paper!
  3. Replies
    3
    Views
    3,847

    [Error Code] Re: Ricoh MP 6001 SC 161-003

    Define "after shipping"
    Has the machine been refurbished by your company and shipped to a customer?
    Has it been shipped to your company by someone else?
    Have you seen it working before shipping?
  4. Replies
    8
    Views
    993

    [Misc] Re: blue color in not printing in spc420dn

    Elvis has left the building!
  5. Replies
    15
    Views
    2,392

    Re: Printing Problem With Ricoh MP4000

    The user seemed to say it works sometimes.

    Duplicate ip?
  6. Thread: SC672

    by tcs04
    Replies
    6
    Views
    2,024

    Re: SC672

    Well done sir!!
  7. Replies
    473
    Views
    156,107

    Poll: Re: I used to know everything....

    I'm in the fortunate position of (in october last year) being able to balance cash etc against years left (?) And giving the finger to the career!


    So, in refence to previous quotes

    The less I...
  8. Replies
    15
    Views
    3,015

    [Misc] Re: Aficio 2075 Fusing Problems

    I may know this one!

    I recall something similar a while ago, there's a small control board behind the bcu related to the pressure lift. If u/s it will cause strange fuser faults including the ones...
  9. Replies
    6
    Views
    4,190

    Re: mp c4500 fault code sc 221

    So, this happened after you changed parts?
    1st try sp2111 003 several times, if this works try 2111 001. If ok.... fixed!

    Check there is no obstruction on the right hand door, if this isn't fully...
  10. Replies
    17
    Views
    3,022

    [Jamming] Re: Ricoh 1075 Skewing, jittering, Buckeling

    Be careful using cheat sheets!
    They changed the parts on these machines as they progressed through 1065/ 75, into 2075 and then into the 6000 series. At one point the mylars changed, can't remember...
  11. Thread: SC544 of MPC2003

    by tcs04
    Replies
    16
    Views
    4,093

    Re: SC544 of MPC2003

    I do the same, using an old thermistor lead from AF8000 type. You're right, faster and easier than fuses! I also leave the top fuser cover off for speed.
    We used to do similar on old Brother fax...
  12. Replies
    17
    Views
    3,022

    [Jamming] Re: Ricoh 1075 Skewing, jittering, Buckeling

    Chances of having an AF1075 reg unit...... slim?
  13. Replies
    3
    Views
    772

    Re: Ricoh Pro C900s 254 error code

    I may be wrong, I remember one from a few years ago, drove us crazy! Pull out the fuser and duplex etc and check for paper or debris in ALL the sockets in the rear frame, use a torch and look very...
  14. Replies
    3
    Views
    1,857

    Re: Smart device monitor for admin

    Not something stupid like a duplicate I p address?
    Disconnect and ping the I.p.
  15. Replies
    17
    Views
    3,022

    [Jamming] Re: Ricoh 1075 Skewing, jittering, Buckeling

    Agree with tosko / slimslob, at 1.3m may well need reg mylars. Does the machine have an LCT? These knock out the mylars.Also look for signs of dev spill around the reg gears, could be leaking dev...
  16. Replies
    5
    Views
    1,245

    Re: Ricoh Mpc 6003 (toner not set)

    Note to self.... read previous answers!

    Sorry guys
  17. Replies
    5
    Views
    1,245

    Re: Ricoh Mpc 6003 (toner not set)

    Hard contacts, not rfid, may be dirty?
  18. Replies
    9
    Views
    5,945

    [Error Code] Re: MPC3003 5503 SC899

    This was 8 months ago!
    Of course we updated the firmware
  19. Replies
    7
    Views
    2,830

    [Error Code] Re: Pro1107EX w/ SR5020 - Phantom J001 and SC755

    Mmmmm...... feedback..... Thanks for the update..... good fix!
  20. Replies
    7
    Views
    3,065

    Re: Ricoh MP9000 not recognise finisher SR5000

    Any other Peripherals installed?? (folder etc?)
  21. Replies
    7
    Views
    2,178

    Re: ricoh 7001 jams code J13

    Relay Sensor clean?

    Dev leaking? (Kills feed stations AND Reg / Relay 1 way Bearings) Also Check for tight stepper motors on the feed stations.

    Reg Unit Mylar Guides can wear as early as 450K...
  22. Replies
    9
    Views
    1,684

    Re: MP6000 light copies...230K meter

    Correct. But it's the toner END Sensor. if u/s will not asK for toner and will lose density over 200- 300 copies.

    NEVER use forced toner! Use the "ID check during run" option which Can be used to...
  23. Replies
    7
    Views
    2,830

    [Error Code] Re: Pro1107EX w/ SR5020 - Phantom J001 and SC755

    JAM 001 is a "power on" jam so will show more when you open and close the door.

    I would clean the exit sensors on the black lift plate (and the patches) They get Very dusty. I use my phone camera...
  24. Replies
    75
    Views
    14,381

    [Annoying] Re: Lazy ass techs....

    Been there, done that! spent the last 15 years (ever since we got laptops) saying 1) learn to Search on the laptop and on line, 2) Sort out your accounts with ALL Manufacturers AND save your...
  25. Replies
    75
    Views
    14,381

    [Annoying] Re: Lazy ass techs....

    If you get a call from a "Bob" re a Ricoh colour box, Just say "Sounds like a MUSIC fault" and pause.... You should hear the Brain ticking as they decide whether to ask "What's "MUSIC"? because they...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4