Search:

Type: Posts; User: Jkearbey

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    768

    [Error Code] Re: BizHub C284e ghost duplex jam 14

    Nice, good find. I had something similar happen to me on a Kyocera 4501i. The connector harness on the door where the transfer belt plugs in is very tight and the "prior tech" might have partially...
  2. Replies
    6
    Views
    768

    [Error Code] Re: BizHub C284e ghost duplex jam 14

    Hello,
    Did you replace the UPPER duplex unit (includes the Paper Exit Flag /Sensor) or just the MIDDLE duplex unit (swing out door which also holds the TX Roller) ?
    I have had issues with both...
  3. Thread: c-6950 4551ci

    by Jkearbey
    Replies
    14
    Views
    12,118

    Re: c-6950 4551ci

    In my case it turned out to be the low voltage power supply. Also I can say with high confidence that I have had this code at least 4 other times at different accounts and all of them were resolved...
  4. Replies
    5
    Views
    1,014

    Re: C3850 light on black only

    Definitely check the LSU glass but if they are far from your office then bring a Primary Transfer belt. I have had the BK roller under the belt pop out of its rear holder. Also check the right side...
  5. Replies
    2
    Views
    4,464

    Re: MX5141 E7-14 Error

    Have you already replaced the SCU PWB? One thing that SHARP might tell you if you have tried the SCU PWB and the problem didn't go away is to replace the CCD unit or LENS Unit? They are the same...
  6. Replies
    8
    Views
    2,911

    Re: MX-3610 calibration fail

    This sounds very similar to an issue I had last month??? How do your internal color test prints look? 64-5 , etc. Will it even print that ? It should since its not a calibration SIM but a test...
  7. Replies
    11
    Views
    2,529

    Re: MX-4111N won't Saddle Stitch

    I had an MX-5111 with an FN-10 that wouldn't feed to the saddle tray and I discovered that I couldn't move the saddle staple units in the SIM mode. After trying the usual stuff... firmware,...
  8. Replies
    12
    Views
    6,276

    Re: Sharp MX-6050 does not boot.

    The only way to tell for sure is to check the LED indicators on the MFP PWB. SHARP has a good tech tip /bulletin that explains the LED indicators for a dead machine, TT-051816_1R1. It will help you...
  9. Replies
    2
    Views
    3,217

    [Error Code] Re: ADD STAPLES / staples already loaded...

    I have not had this problem on your model finisher but in the past I have had MX-FN10 saddle stitch finishers display the "add staple" message when staples are inserted and full. On two occasions...
  10. Thread: c-6950 4551ci

    by Jkearbey
    Replies
    14
    Views
    12,118

    Re: c-6950 4551ci

    Hello all

    Just got this code "C6950" on Friday on a Kyocera 3551ci and the machine is down, service manual states that it is an IH PWB failure and tells you to trace back starting at the Low...
  11. Thread: f2-41

    by Jkearbey
    Replies
    5
    Views
    21,943

    [Error Code] Re: f2-41

    I see these F2 codes usually when generic toner is used after a SHARP brand toner was used prior. "F2-40 BK, F2-41 Cyan, F2-42, Magenta, F2-43 Yellow. " Bring spare color DV with you and if you...
  12. Re: How to change Admin password back to factory (admin) MX-3140N

    Hello,

    The short answer is Yes.

    Unlike the older models where you could reset it back to "admin" inside the simulation fairly quickly, SHARP has increased their security levels around this...
  13. Replies
    8
    Views
    587

    Re: Glad to be on board!

    Thank you everyone
  14. Replies
    8
    Views
    587

    Glad to be on board!

    Hello All,

    My area of experience & training is primarily SHARP and KYOCERA. I am also trained on MURATEC and have field experience on many others but not officially trained. Thanks for the great...
  15. Replies
    3
    Views
    14,222

    [Error Code] Re: U2-91 clearable code

    Hello All,

    I too have dealt with this very aggravating intermittent error code. The first time I had the error code was 3 years ago on a SHARP MX-503N. On that account it would reset but continue...
Results 1 to 15 of 15