I actually ended up filing a bit of the edge of the catch on the clutch off and greasing it ... Seems either the solenoid gets weak or the machine doesn't fire it long enough, but this worked for me...
Type: Posts; User: GottaFixEmAll
I actually ended up filing a bit of the edge of the catch on the clutch off and greasing it ... Seems either the solenoid gets weak or the machine doesn't fire it long enough, but this worked for me...
P.S. The unit in question is the one above the exit unit that does offset stacking and has the two fans attached to it ~ the customer does not have a finisher or sorter or job separation tray ...
Before I start, I have both Service and Parts manuals for this model ~ anyone needs them I'll send them to you for free ...
I have replaced the Sub-Frame that houses the Developer, Drum, & Fuser...
Hi have a problem with Konica bizhub 7222, inconsistent lead edge registration, it's happening with both trays - acts as though it feeds early at times - but it goes away at times, any ideas ?? Thanks
Hi, I wrote in awhile ago about jamming at the delivery / turnover area, the machine has the FN-6 finisher and it was suggested that the gate that either lets the paper go into the finisher or paper...
Hi, I've written in before ... I'm having an issue with jamming in the Delivery / Reversal unit just above the fuser. The Machine is equipped with the FN-6 finisher and the AR-DU4 ( standard, I...
Sorry didn't think to write down the codes, and I know better ... I have the factory manual. I believe it's the FN7 but if I take it off it duplexes well ???, the copy partially exits and its when it...
I have a problem with Duplex jamming ... the paper partially exits the top, goes back in but will skew and or jam, running in to a piece of paper thats exiting the fuser ?? if I remove the...
Maybe a shelf ?? ............ I work on a lot of old equipment, being an independent ... still have some 2028's / 3035's and even an old 2590 --- 29 years !! 18 as an indepent ...
Time to retire...
Customer is just about ready to give up on this machine ... I also replaced a Motor Control Board and Paper Feed Motor 1, 2 weeks ago !! ( had no drive to PFM1 but could drive the others thru...
HI, I have a Konica 7135 that is overtoned to the point of background and displaying trouble code F26-3, I replaced the Developer 2 weeks ago - the L detect set-up went as usual and displayed "OK"...
Looking for the parts manual for the ADF model # MR3006, I believe ... it was used on the DP2460 and 3580, I'm looking for part numbers on the exit unit ( ADF ) the little drive belt and the exit...
Error code "d" ??? never seen this one before ... keys on op panel don't do anything, can't get into diagnostics !! no sub-codes possible as a result ...
Think it's fried ( surge ), any ideas ??...
Sounds like the car companies, change a bit of trim, offer a new choice of colors and it's a new model !!
Well ... probably !! cuz I could swear it worked last time !! the office this one is in is connected - and I'll bet someone had printed to it ...
Would the error code cause it to stay in either...
Fatal Error 122 ... refers to power supply fan, didn't have one ... but my book was for an earlier model !! I went out to the customer and he had the code but it went away and never came back while I...
Hi, I have one of these that shows an error code: U2-23, a memory error that can be reset with sim 16, problem is that it doesn't seem to have the same code to get into diagnostics as the older...
Anyone have a PDF of this one ??? Appreciate it, Thanks ..... Mike
It was the CCD cable, where it plugs into the MCB ... the clamp piece must have not been in far enough.
Thanks for the help !!
Mike
I'll check the CCD cable today ... had a bit of tfouble getting it back in because I tried to thread it thru the MCB cage after bolting it to the machine and those flat magnet filter thingeys kept...
Neither of the two images look like the back of that AR-207, but the point is valid ... the smaller 4 wire cable powering the lamp was ... I believe loose because when I made sure it was seated the...
Just replaced the Laser unit: L6-10 code, reassembled and now I have a F5-02 code which refers to a lamp problem ?? the lamp lights and the optics seek home position ... the odd thing is that the...
E7-11 code ... CCD White Level Trouble: CCD drive circuit (CCD PWB, ASIC harness) trouble Copy lamp lighting trouble (Copy lamp, inverter PWB) .................
This machine has been on my shelf...
In a previous post I mentioned that the pf clutches are not firing. I have since accessed them in diagnostics and they do indeed work ... The machine indicates that it has no paper after failing to...
It is a leap !! ... although 99.9 % sure, being an independent and not having similar machines in stock, you have to pop for a board and hope that fixes it ... I will talk to my Board Repair facility...