Search:

Type: Posts; User: Staggan

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Thread: DX3243 PriPort

    by Staggan
    Replies
    9
    Views
    1,326

    Re: DX3243 PriPort

    Hello

    Yes, I am adjusting paper type using that lever...

    Thanks
  2. Thread: DX3243 PriPort

    by Staggan
    Replies
    9
    Views
    1,326

    Re: DX3243 PriPort

    Update

    I have got normal thickness paper working fine, but thicker paper is still slipping....

    I think the issue is pressure on the registration roller which is managed via part of the drum...
  3. Thread: DX3243 PriPort

    by Staggan
    Replies
    9
    Views
    1,326

    Re: DX3243 PriPort

    Thanks for the suggestion...

    I've checked the grub screws on both the motor and roller, checked belt condition and tensioner the belt again...

    Still no joy, the position can fluctuate by 10mm...
  4. Thread: Ricoh DX3243

    by Staggan
    Replies
    2
    Views
    5,361

    Ricoh DX3243

    Hello

    I posted the below... and I wondered if someone in this forum could help..

    I am looking for some advice on a Ricoh PriPort machine...

    The image is randomly moving up and down the...
  5. Thread: DX3243 PriPort

    by Staggan
    Replies
    9
    Views
    1,326

    Re: DX3243 PriPort

    Hello

    Yes, registration is moving, but there is no registration clutch shown in the service manual...

    I will try posting in the digital duplicator forum...

    Thanks
  6. Thread: DX3243 PriPort

    by Staggan
    Replies
    9
    Views
    1,326

    DX3243 PriPort

    Hello

    I am looking for some advice on a Digital Duplicator, PriPort machine...

    The printed text is randomly moving up and down the page....

    I have replaced both the pickup and feed roller,...
  7. Thread: Toshiba 557

    by Staggan
    Replies
    1
    Views
    684

    Toshiba 557

    Hello

    I am after some ideas on an issue...

    I have an E-Studio557 mono machine which for low copy / print runs appears fine...

    However at around 300 - 350 copies the copies start to fade and...
  8. Replies
    11
    Views
    3,804

    Re: MP C4501 Paper sensor

    Thanks for all the assistance.

    There were several issues...

    The sensor at the bottom of the secondary transfer unit was faulty, the duplex exit sensor was dirty and one of the one way bearings...
  9. Replies
    11
    Views
    3,804

    Re: MP C4501 Paper sensor

    Jam code is J001

    Will get back out to the machine and check the suggestions on here...

    Thanks
  10. Replies
    11
    Views
    3,804

    Re: MP C4501 Paper sensor

    I'll check the jam code and check service mode sensor inputs...

    The jam is permanent, as in it is occurring straight from power on, hence my conclusion it was a sensor and the sensor at that...
  11. Replies
    11
    Views
    3,804

    MP C4501 Paper sensor

    Hello

    I have an issue with a machine constantly reporting a jam at position Z. Position Z is behind the secondary transfer unit in the duplex door.

    There is no paper jam and I have tried...
  12. Thread: IR C5051

    by Staggan
    Replies
    1
    Views
    795

    IR C5051

    Hello

    After some advice.

    Have an IR C5051 which is showing the green power light but will not come to ready...

    I turn the machine off via the side button... turn it back on, green light but...
  13. Replies
    12
    Views
    27,919

    Re: Sharp MX3550 error code L4-11

    Thanks for the information.. new board ordered
  14. Replies
    12
    Views
    27,919

    Re: Sharp MX3550 error code L4-11

    Hello

    Did that already... seems to move freely.. but not sure how free it should be...

    Also, if you leave the motor attached you can still slide the unit and feel the motor moving.. which also...
  15. Replies
    12
    Views
    27,919

    Re: Sharp MX3550 error code L4-11

    The shifter unit actually appears to run freely.. nothing preventing it from moving side to side... I don't think it is one the sensors either as even in the middle position it is juddering /...
  16. Replies
    12
    Views
    27,919

    Sharp MX3550 error code L4-11

    Hello
    This machine is giving a juddering / clicking noise from the shift unit.. no internal finisher attached.

    I removed the shift unit and the housing around the motor had melted, causing it to...
  17. Re: MP C4501 Skew when copying but fine when printing

    Hello

    Yes, it was doing it on both....

    It seems with a little brute force and some minor twiddling with the carriage cable fixings I now have it straight...

    Thanks for all the help....
  18. Re: MP C4501 Skew when copying but fine when printing

    I've looked at comparable images again... and I don't think it is actually skewing the image

    If I take a meter reading, it is fine, if I take a copy of that the bottom of the leading edge, for...
  19. Re: MP C4501 Skew when copying but fine when printing

    Not sure I understand which holes...

    Can you direct me in the manual or with a picture.. ? Thanks

    I would have thought there would be a way to rotate the scanned image slightly in service or in...
  20. Re: MP C4501 Skew when copying but fine when printing

    I was afraid the scanner may be skewed...

    No ping from the glass, all seems to be seated properly.. and mirrors all seem to be in place...

    Is there any adjustment to fix this sort of issue...
  21. Re: MP C4501 Skew when copying but fine when printing

    Any suggestions on being able to resolve it?

    Thanks
  22. MP C4501 Skew when copying but fine when printing

    Hello

    I have an MP C4501 which is skewing copies from the scanner glass but when printing it is fine.

    I've checked the manual and cannot find anything overly helpful and wondered if anyone had...
  23. Replies
    4
    Views
    1,873

    Re: MP C4501 not waking up

    Thanks for the update, machine now seems fine.

    I'll add this to our list of issues we've not seen for future reference.

    Thanks again.
  24. Replies
    4
    Views
    1,873

    Re: MP C4501 not waking up

    Hello Cipher

    Thanks for the suggestion.. that seems to have resolved it.

    What is the reasoning behind this causing a problem?

    Thanks
  25. Replies
    4
    Views
    1,873

    MP C4501 not waking up

    Hello

    I have an MP C4501 that is refusing to wake up after going to sleep...

    First thing I did was update firmware, which made no difference.

    Then I replaced the control panel, checked...
Results 1 to 25 of 54
Page 1 of 3 1 2 3