Hello
Yes, I am adjusting paper type using that lever...
Thanks
Type: Posts; User: Staggan
Hello
Yes, I am adjusting paper type using that lever...
Thanks
Update
I have got normal thickness paper working fine, but thicker paper is still slipping....
I think the issue is pressure on the registration roller which is managed via part of the drum...
Thanks for the suggestion...
I've checked the grub screws on both the motor and roller, checked belt condition and tensioner the belt again...
Still no joy, the position can fluctuate by 10mm...
Hello
I posted the below... and I wondered if someone in this forum could help..
I am looking for some advice on a Ricoh PriPort machine...
The image is randomly moving up and down the...
Hello
Yes, registration is moving, but there is no registration clutch shown in the service manual...
I will try posting in the digital duplicator forum...
Thanks
Hello
I am looking for some advice on a Digital Duplicator, PriPort machine...
The printed text is randomly moving up and down the page....
I have replaced both the pickup and feed roller,...
Hello
I am after some ideas on an issue...
I have an E-Studio557 mono machine which for low copy / print runs appears fine...
However at around 300 - 350 copies the copies start to fade and...
Thanks for all the assistance.
There were several issues...
The sensor at the bottom of the secondary transfer unit was faulty, the duplex exit sensor was dirty and one of the one way bearings...
Jam code is J001
Will get back out to the machine and check the suggestions on here...
Thanks
I'll check the jam code and check service mode sensor inputs...
The jam is permanent, as in it is occurring straight from power on, hence my conclusion it was a sensor and the sensor at that...
Hello
I have an issue with a machine constantly reporting a jam at position Z. Position Z is behind the secondary transfer unit in the duplex door.
There is no paper jam and I have tried...
Hello
After some advice.
Have an IR C5051 which is showing the green power light but will not come to ready...
I turn the machine off via the side button... turn it back on, green light but...
Thanks for the information.. new board ordered
Hello
Did that already... seems to move freely.. but not sure how free it should be...
Also, if you leave the motor attached you can still slide the unit and feel the motor moving.. which also...
The shifter unit actually appears to run freely.. nothing preventing it from moving side to side... I don't think it is one the sensors either as even in the middle position it is juddering /...
Hello
This machine is giving a juddering / clicking noise from the shift unit.. no internal finisher attached.
I removed the shift unit and the housing around the motor had melted, causing it to...
Hello
Yes, it was doing it on both....
It seems with a little brute force and some minor twiddling with the carriage cable fixings I now have it straight...
Thanks for all the help....
I've looked at comparable images again... and I don't think it is actually skewing the image
If I take a meter reading, it is fine, if I take a copy of that the bottom of the leading edge, for...
Not sure I understand which holes...
Can you direct me in the manual or with a picture.. ? Thanks
I would have thought there would be a way to rotate the scanned image slightly in service or in...
I was afraid the scanner may be skewed...
No ping from the glass, all seems to be seated properly.. and mirrors all seem to be in place...
Is there any adjustment to fix this sort of issue...
Any suggestions on being able to resolve it?
Thanks
Hello
I have an MP C4501 which is skewing copies from the scanner glass but when printing it is fine.
I've checked the manual and cannot find anything overly helpful and wondered if anyone had...
Thanks for the update, machine now seems fine.
I'll add this to our list of issues we've not seen for future reference.
Thanks again.
Hello Cipher
Thanks for the suggestion.. that seems to have resolved it.
What is the reasoning behind this causing a problem?
Thanks
Hello
I have an MP C4501 that is refusing to wake up after going to sleep...
First thing I did was update firmware, which made no difference.
Then I replaced the control panel, checked...