As FrohnB mentioned, you can use the Service mode to simply format the HDD and call it a day if they don't need an actual data erasure. However, depending on the customer/contract, you may need to do...
Type: Posts; User: Xcelsior
As FrohnB mentioned, you can use the Service mode to simply format the HDD and call it a day if they don't need an actual data erasure. However, depending on the customer/contract, you may need to do...
Authentication setting is in User Tools, I believe on the second page of Interface Settings.
If the screen shows the IP you put in (192.168.x.x) but when you print a config page it shows 10.11.x.x then try checking that the 802.x Authentication (I forget the exact name) wasn't turned on.
If...
In case it's needed, the SP for that is SP 5-081-001 "[ServiceSP Entry Code Setting] DFU".
The MP 305SPF (Smart OP) is 806182 entered from one of the Classic Screens or the On-Screen Service Mode Keypad (rec'd to use the Keypad).
The MP C305 (Normal OP) is 107 entered from any of the...
All it's ever listed as is:
Vsg: ID sensor output when checking the bare drum.
Vsp: ID sensor output when checking the ID sensor pattern.
But I believe it's along the lines of:
Vsg = Voltage...
You've eliminated the machine as the issue if others, and yourself, can print to it without issue. It's not the network if you can plug in to the connection that a troubled PC was using and print...
I know I always had to put some TriFlow on every bearing/shaft under the front cover, rear cover, and a few visible gears/etc at the back/bottom of the the Transport Belt (as viewed with the...
TriFlow is what they always gave Ricoh Techs, works perfectly for so many noises.
I would always put a few drops on a finger and just run it over the rails. Never had the noise come back. :)
Assuming the thermistors are in place properly and the code was reset after with SP 5-810; Check that you didn't pinch a wire, then check the Thermostats, then check the lamp.
If you can't get...
Without looking around in the menus I don't know if it's there, but in WIM it will be called 'RC Gate' so you won't likely see @Remote/AMR. Course if they changed that since the x03 models I'm outta...
I doubt it will help, but if you care to try, I still have the FW for that model around.
As Slime mentioned, check the power supply or power line.
The other thing is to make sure the thermistor wires aren't pinched/damaged. If the metal bracket pinches one too tightly and gets through...
The "Random" SC672s is worrying. It is possible for that to occur if you cycle the power too often too fast, but outside of that the CTL could just as easily be shot. And with the Fax having so many...
As mentioned, make sure the small blue jumper on the fax board is set to ON. Even on machines with the board installed at the warehouse the jumper can be forgotten and you just have to change it....
As Guitar mentioned, set the settings on the copy screen as you want them then hit "Program" and then "Program as Default". Once that's done the Copy screen will default to those settings after...
We (Ricoh) were recently massively back-ordered on 1027s so a lot of 1027-R units got shipped out. The 1027-R (Recycled) are rebuilt to...questionable quality. Sometimes they last just fine for 60K,...
The following parts are unique for D127/D128. When replacing the following parts, usethe parts specified for each model. DO NOT mix up the following parts for D115/D116and D127/D128. Otherwise, both...
As has been mentioned, update the Firmware. SC899 is just a software error that any number of things can cause. Printing from a Browser causes it a lot and a PCL firmware updates mostly fixes that....
While Firmware is usually the best fix, in this case the 402 does not currently have FW known to fix SC899 from most causes.
The only SC899 correction as of yet for the 402 is;
SC899 may occur...
The guide states the following about Heavy/Glossy Paper;
35291 Tray 1 16-68lb Stock. Tray 2 16-45lb Stock. Bypass 13.8-68lb Stock.
35292 Tray 1-2 Plain Paper types. Tray 3-4 Gloss, coated,...
SC 899 is almost always going to just be a software bug. Often it happens when printing from IE, but really any internal app can cause it as well. If a print job was sent to it, you'll have to clear...
At that point, SC 372 is a TD Sensor Adjustment Error. It would be worth checking the TD snsr and connector while at the machine.
For the Mp 4001 there is no SC 375 error. Is it possible it was an SC 355 (Grayscale measurement error)? 355 would indicate either normal PCU maintenance is needed, or the laser shield glass is...