Check to make sure that both finisher trays are level, if they are not it will bind up and you will get that code.
Type: Posts; User: gregoryrbrts
Check to make sure that both finisher trays are level, if they are not it will bind up and you will get that code.
Why would you be changing just the web. That particular model the whole fuser should be changed at the same time as the web. If it is a matter of just rebuilding you should be changing out gears at...
The original call was for please wait which usually points to the hard drive. Ordered the hard drive and when doing CN update the ICUM was telling me Rom Unusual. I have also tried swapping the PCU...
Here are a couple of things to try. Try switching simulation 55-3 bit 6 switch 1 to 1, if it is already switched to that turn it back to 0. Also try turning off WSD under the network port settings....
I'm pretty sure that you have a bad MFP flash Rom. Try changing them to see if that fixes it. Hanging up like that, it could also be the hard drive.
The problem is your SD card, according to the service manual you are supposed to back up the data but don't because then you will backing up corrupted data. Once you replace it the machine should...
First, this is a copier forum not politics.org. I voted for Trump and will vote for him again in 4 years. Why is a person from Canada worried about a country that is not your own. Sounds like you...
Your part # for the stapler is 0jpcrt590n-s/. They don't list this part in the parts guide but it is in a Tech Pub. By the sounds of what is happening with the springs it sounds like the stapler has...
Maintenance code AA means that both the black supplies and color supplies are at the end of life. That being said just resetting the counters is not good because then you are going to leave your...
here is your problem, the spring under your set pad is too weak, order a new one and that will fix your problem. Just recently had the same problem just on Friday. replaced the part today and all is...
I am a Sharp tech in Illinois and hope I can help, here are two things to try. 1. Try using the original count feature on your copier to count your originals, it is under special functions. Also web...
Using the customers paper you wont get a true calibration and from that point on the machine would just not be quite right. The colors will be off because regular paper it soaks in too much and I...
So I asked for some more info and here is what I found out. It charges based on paper coming out of machine and charges can only be set up for different sized paper. So here is my thought, for email,...
The age of that particular may be your downfall because it may not be compatible with the updated software of that particular model. The newer model is what we used, that is the only thing that may...
[QUOTE=gregoryrbrts;564352]Unfortunately I do not know the vendors name but the coin op is an ACDI.[/QU
I'm not sure why ACDI would tell you that, from my understanding all the coin op does is...
Unfortunately I do not know the vendors name but the coin op is an ACDI.
so I found out some info for you. with the harness kit it should be no problem hooking up the coin op, the only downfall with the older coin op it may not be compatible with the new machine. We...
I believe the same capabilities that allow you to make copies with the coin op will also allow you to do fax and email. I will look into this for you but unfortunately the tech that set it up is out...
It is possible to set machine up with coin op capabilities, I know this because my dealership just recently set one up. Details I do not know because I was not the tech that set it up but do know...
This is possible as my dealership just recently set one up for that. Details I do not know because another tech did the setup but do know it is possible. It was on a mx5070
I will bet that the problem was coming from a scratched drum, process unit ill bet process unit did not need replaced. More than likely just the drum and MK
any problems like that where the copy looks like that I would say that would be your laser unit.
We have also had problems with machines not in fast wakeup, I have also noticed that the checkbox after remote job is finished, not sure what the rest says but is the second checkbox right below...
I love how people claim to be techs on here but don't know how to calibrate a machine. If you are changing dv or drum then first comes 25-2 bwith toner out. After stir is done leave sims and when...
As like other Sharp models, check the fuser web to see if it is clogged. I have seen after big copy jobs that the fuser web does not move forward as fast as the copies can so the web gets clogged...