Search:

Type: Posts; User: Ratchet2501

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    31
    Views
    7,498

    Re: Change in profession

    Reimbursement model covers 24mpg, not my 2003 Tahoe. Been trying to sell it and get something more gas savvy but so far no luck. Done over seven thousand miles in six or seven weeks.
  2. Replies
    31
    Views
    7,498

    Re: Change in profession

    True that. I used to be oilfield for five years. This work is much safer though not as well paying, for now. My only real complaint at the moment is using my vehicle for everything. But, there are...
  3. Replies
    31
    Views
    7,498

    Change in profession

    Been a while but I'm back. Now a Xerox IT analyst instead of a sharp technician. I am finding that in some ways I dig Xerox a LOT more than sharp but in a few ways I'm still a fish out of water when...
  4. Re: Xerox B8090 Booklet issue with Indesign Mac

    Yes it is the Altalink. The screen shot is on a thread somewhere else reflecting the area where my machine gets weird. The second check on disable booklet layout is what just resets everything back...
  5. Xerox B8090 Booklet issue with Indesign Mac

    I have an issue with the stated machine not printing booklets properly.
    https://xerox.i.lithium.com/t5/image/serverpage/image-id/6850i67D1F25EFCAFC2AA/image-size/original?v=v2&px=-1
    This is the...
  6. Replies
    23
    Views
    5,261

    Re: Mx-c312 prints light on left side

    Customer brought the machine in and after fiddling with the LSU and getting nowhere I tried re-replacing the developer cartridge and even though the other had a good 25-2, it fixed the problem. I am...
  7. Thread: Hi there

    by Ratchet2501
    Replies
    7
    Views
    1,006

    Re: Hi there

    Welcome
  8. Replies
    1
    Views
    1,437

    Sharp Mx-m363n Firmware request

    Sharp Mx-m363n Firmware request. Has a HDD but no Security.
  9. Replies
    23
    Views
    5,261

    Re: Mx-c312 prints light on left side

    I used the cleaning wand and checked it out with my light, seemed alright but the results speak for themselves. Next time I go there, I'm pulling the lsu (looks like a pain on this one) and checking...
  10. Thread: Newbie

    by Ratchet2501
    Replies
    7
    Views
    973

    Re: Newbie

    Welcome
  11. Replies
    23
    Views
    5,261

    Re: Mx-c312 prints light on left side

    Seems like it is. Can that cause such an isolated defect in printing just on the one color?
  12. Replies
    23
    Views
    5,261

    Re: Mx-c312 prints light on left side

    39272

    Copy of the 64-5 B/W shows left side of sheet pretty much blank, readable but not very dark.
  13. Replies
    5
    Views
    1,168

    Re: Sharp Mx-m363n trimming copy edges

    Update: Sim 48 had some weird settings 50, 63, 50, 76 and 50. Assuming that 50 is the default/middle ground I reset everything to 50 across the board. Looked better, until I reran the 50-28...
  14. Replies
    10
    Views
    2,233

    Re: Customers, getting smarter every day

    I can't even recall how many times in the last year I've been doing this I've had half the machine's guts on the floor and I hear "I can't print can I?".
  15. Thread: Hello

    by Ratchet2501
    Replies
    4
    Views
    959

    Re: Hello

    Welcome
  16. Replies
    23
    Views
    5,261

    Re: Mx-c312 prints light on left side

    I could easily look past them not mentioning the mx-c312 but this talks about the ends going through not one side. I will scope it out when I'm digging around in it. Going to try re-replacing the...
  17. Replies
    23
    Views
    5,261

    Re: Mx-c312 prints light on left side

    Fuser, transfer belt, drum assembly and developer are all new. Replaced the transfer belt today since I didn't see anything immediately wrong with it, still light on the left side. Going to hunt down...
  18. Replies
    5
    Views
    1,168

    Re: Sharp Mx-m363n trimming copy edges

    I need to get better about snagging copies of crap like this, get creative that way nothing is publicized about the customer and such. Recently I struggled with a job interview because of my "habit"...
  19. Thread: Hii

    by Ratchet2501
    Replies
    4
    Views
    855

    Re: Hii

    Welcome to the forums
  20. Thread: hi

    by Ratchet2501
    Replies
    6
    Views
    961

    Re: hi

    o7 from naples utah U.S., how's the weather over there?
  21. Replies
    5
    Views
    1,168

    Sharp Mx-m363n trimming copy edges

    I have a machine that has started to trim the width of a copy by maybe a tenth of a inch. I have run through the gamut of 50-28 calibration and while that made it better, it's still taking some of...
  22. Replies
    14
    Views
    2,967

    Re: I resigned today

    May your neighbors respect you,
    Trouble neglect you,
    The angels protect you,
    And heaven accept you when the time comes.
  23. Replies
    6,528
    Views
    15,055,046

    Re: Just how Crazy is Donald Trump!

    Nope, nothing would get done. *facedesk*
  24. Replies
    6
    Views
    1,689

    Re: MX-M354N DF jams

    Stupid sensors anyhow
  25. Replies
    23
    Views
    5,261

    Re: Mx-c312 prints light on left side

    The fuser was replaced recently but forgive my lack of copier experience but that doesn't seem like it would affect a single color without all four going to crap. Secondary transfer system is a...
Results 1 to 25 of 212
Page 1 of 9 1 2 3 4