User tools printer features. reset 802.xx to default. cycle power
Type: Posts; User: Tatteous
User tools printer features. reset 802.xx to default. cycle power
Reset>806182>## C
Right click printer driver-printer properties- ports- configure port. this should be using the machine's IP address. If it is using a Windows driver do a full clean uninstall. Configure port. Set to...
Go to printer driver properties, ports, configure port, use LPR (not RAW) port name lp (Lower case LP). check the box for LPR Byte Count Enable. Deselect SNMP unless they are using it. Use the...
If you know how to color balance...
4.19.6 PRINTER GAMMA CORRECTION
The ACC is usually sufficient to adjust the color balance to get the best print output. You
only need the printer gamma...
B2969645 is the DV#. Change this when you get weak blacks or dirty edges. SP2801 to init the dv.
You don't actually remove the spring. You lessen the tension. Only on the 55 and 60 speed machines.
What I am to understand is that you have a magnification problem. Place your scale on the glass and make a copy of it. It the copy is the exact same length as the scale, then run the copy that you...
I would look into the print driver. Machine specific PCL6 is the only way to go. Go under print server properties and do a thorough clean install of the driver.
Convert the page to a PDF and save...
Cheat both switches of the front door.
Take the cleaning web off of the fuser and push the fuser back into the machine while holding the web assy in your hand. SP mode 5804 055. This will tell you...
I clear all WSD driver and auto port drivers. Then install in Win10 with the "my machine wasn't found" and use the IP address like in Win7 Machine specific PCL6 driver only.
Use RAW port. Que name...
The shape of the PTR has been changed. It should be replaced with new for best results.
5515 010 set to 0
5515 011 set to 0 (per Ricoh)
Go into the Web Image monitor. Auto email Notification and delete and fields that have values.
5816 209 is only to clear an @ remote installed...
I replaced the motor for the developer drive/ toner add clutch. It did not resolve the issue.
I had the same problem. It was the CIS. It was less money to buy a high meter used machine than it was to replace the CIS.
All firmware needs to be current especially NCS.
Win 10 has more steps. Try this..
https://www.youtube.com/watch?reload=9&v=daijaCPWSBs
This model requires thick1 or middle thick to fuse properly using 28# paper.
[QUOTE=Foo;606071]Went to a call yesterday for an SC 552 on a MP C4503.
Checked some things and did a reset of the fuser error.
Fuser reset properly and the machine ran fine.
I was completing...
The bearing need to be lubed. I have had many of this model have bad heat roller bushings, They are melted onto the heat roller and need to be chipped off the use sand paper to clean the remnants off...
I used a dremmel tool to slightly bore out the holes in the metal metering blade in the toner supply unit. Tech services had nothing to say. I even bought a new DV motor which has the toner supply...
All PM parts are good. All OEM parts and toner. I followed the bulletin regarding the mag roller. I even cleaned the doctor blade. On the 6002 that I enlarged the toner hopper holes on, it is running...
There is a bulletin about the tines on the ptr. They stick out after a jam removal. Replace the PTR. If possible, use a scale to accurately measure both sides of the lead edge to see if the paper is...
On the MP 6002 I had to bore out the toner holes that feed into the developer unit to keep from getting light images. I tried supply mode down to 600 and scrubbed clean and regapped the doctor blade....
If you do a RAM clear, you will be faced with the machine being in Japanese and possibly inability to use @remote, never do ALL CLEAR.