Search:

Type: Posts; User: Tatteous

Search: Search took 0.02 seconds.

  1. Replies
    12
    Views
    4,638

    Re: Ricoh reset network settings

    User tools printer features. reset 802.xx to default. cycle power
  2. Replies
    7
    Views
    6,355

    IM C4500 SOP SP mode

    Reset>806182>## C
  3. Re: MP C3503 - Can't print Multiple Sets with PCL6

    Right click printer driver-printer properties- ports- configure port. this should be using the machine's IP address. If it is using a Windows driver do a full clean uninstall. Configure port. Set to...
  4. [Misc] Re: Lanier MP C2500 Printing random symbols when printing emails

    Go to printer driver properties, ports, configure port, use LPR (not RAW) port name lp (Lower case LP). check the box for LPR Byte Count Enable. Deselect SNMP unless they are using it. Use the...
  5. Replies
    10
    Views
    6,509

    Re: MPC4503 color matching to MPC4500

    If you know how to color balance...

    4.19.6 PRINTER GAMMA CORRECTION
    􀂃 The ACC is usually sufficient to adjust the color balance to get the best print output. You
    only need the printer gamma...
  6. Thread: Sp8300DN

    by Tatteous
    Replies
    8
    Views
    2,985

    Re: Sp8300DN

    B2969645 is the DV#. Change this when you get weak blacks or dirty edges. SP2801 to init the dv.
  7. Replies
    16
    Views
    7,231

    Re: Ricoh MP C4503 C5503 C6003 wax lubricant bar

    You don't actually remove the spring. You lessen the tension. Only on the 55 and 60 speed machines.
  8. Thread: ricoh sp5200s

    by Tatteous
    Replies
    25
    Views
    6,071

    Re: ricoh sp5200s

    What I am to understand is that you have a magnification problem. Place your scale on the glass and make a copy of it. It the copy is the exact same length as the scale, then run the copy that you...
  9. Replies
    12
    Views
    4,701

    Re: Ricoh MPC4503 fusing issues...

    I would look into the print driver. Machine specific PCL6 is the only way to go. Go under print server properties and do a thorough clean install of the driver.
    Convert the page to a PDF and save...
  10. Replies
    12
    Views
    19,846

    [Error Code] Re: MP6002 sc540-03

    Cheat both switches of the front door.
    Take the cleaning web off of the fuser and push the fuser back into the machine while holding the web assy in your hand. SP mode 5804 055. This will tell you...
  11. Replies
    30
    Views
    7,369

    Re: printer driver settings lost in windows 10

    I clear all WSD driver and auto port drivers. Then install in Win10 with the "my machine wasn't found" and use the IP address like in Win7 Machine specific PCL6 driver only.
    Use RAW port. Que name...
  12. Replies
    23
    Views
    7,557

    Re: Mpc4502 wrinkling through fuser

    The shape of the PTR has been changed. It should be replaced with new for best results.
  13. Replies
    14
    Views
    19,286

    Re: supplies order has failed - Black

    5515 010 set to 0
    5515 011 set to 0 (per Ricoh)

    Go into the Web Image monitor. Auto email Notification and delete and fields that have values.

    5816 209 is only to clear an @ remote installed...
  14. Replies
    13
    Views
    7,664

    Re: Light image MP 6002

    I replaced the motor for the developer drive/ toner add clutch. It did not resolve the issue.
  15. Thread: mpc 4502

    by Tatteous
    Replies
    9
    Views
    2,050

    [Misc] Re: mpc 4502

    I had the same problem. It was the CIS. It was less money to buy a high meter used machine than it was to replace the CIS.
  16. Replies
    17
    Views
    18,281

    Re: MP201 Windows 10 scan to folder

    All firmware needs to be current especially NCS.

    Win 10 has more steps. Try this..

    https://www.youtube.com/watch?reload=9&v=daijaCPWSBs
  17. Replies
    5
    Views
    1,392

    Re: Ricoh MP C5501

    This model requires thick1 or middle thick to fuse properly using 28# paper.
  18. Re: MP C4503 Scan to email destinations disappeared...

    [QUOTE=Foo;606071]Went to a call yesterday for an SC 552 on a MP C4503.

    Checked some things and did a reset of the fuser error.
    Fuser reset properly and the machine ran fine.

    I was completing...
  19. Replies
    35
    Views
    4,995

    [Jamming] Re: Ricoh MP C2500 - jamming in fuser

    The bearing need to be lubed. I have had many of this model have bad heat roller bushings, They are melted onto the heat roller and need to be chipped off the use sand paper to clean the remnants off...
  20. Replies
    13
    Views
    7,664

    Re: Light image MP 6002

    I used a dremmel tool to slightly bore out the holes in the metal metering blade in the toner supply unit. Tech services had nothing to say. I even bought a new DV motor which has the toner supply...
  21. Replies
    13
    Views
    7,664

    Re: Light image MP 6002

    All PM parts are good. All OEM parts and toner. I followed the bulletin regarding the mag roller. I even cleaned the doctor blade. On the 6002 that I enlarged the toner hopper holes on, it is running...
  22. Replies
    23
    Views
    7,557

    Re: Mpc4502 wrinkling through fuser

    There is a bulletin about the tines on the ptr. They stick out after a jam removal. Replace the PTR. If possible, use a scale to accurately measure both sides of the lead edge to see if the paper is...
  23. Replies
    13
    Views
    7,664

    Light image MP 6002

    On the MP 6002 I had to bore out the toner holes that feed into the developer unit to keep from getting light images. I tried supply mode down to 600 and scrubbed clean and regapped the doctor blade....
  24. Replies
    7
    Views
    1,940

    [CQ] Re: Ricoh C3002 way too dark when prnt

    If you do a RAM clear, you will be faced with the machine being in Japanese and possibly inability to use @remote, never do ALL CLEAR.
Results 1 to 24 of 24