recently I've been getting a problem finisher is a DF 710 on a FS 9530. is already has gone through 3 springs that cause Tray a to lower and throws a code. Any fix or tipd for that or do I keep on...
Type: Posts; User: Dr.silver
recently I've been getting a problem finisher is a DF 710 on a FS 9530. is already has gone through 3 springs that cause Tray a to lower and throws a code. Any fix or tipd for that or do I keep on...
Printer Toner Cartridges - Copier Toner Cartridges - Printer Parts & Copier Parts
They are good and reliable :)
Fix I read
Bulletin #
KM-3050/4050/5050-10
To Improve Operation Efficiency, the DR-710 has been modified and the description changed to the
DR-711. Be sure to identify the Drive Section...
Reason I am asking one of our techs took out the Engine Board out and replaced it in the Kyocera 5050 but used a Copystar board. The Plug to the Developer Clutch is no where on the board. When making...
Thanks for all the help. It's cleared :D
I currently Required a Sharp MX M363n. I have clean the machine and replaced all the units. Only issue I have is the screen Reads *maintenance required.code.ta* I have tried to get into Simulation...
I had a lady wanting me to look at her Sharp.While looking at it I clean the Machine and when I turn it on I got a Error L4-30 and cant shake it anyone have any Ideas:confused:
Drum unit is moving nicely and I clean waste toner as well. Still Dragging and bogging up.
I am dying here. I am have problem with a 1128mfp it Bog downs you can hear it bog. and it get worse and worse. I cleaned all the Clutches, Cleaned the fuser and replaced the Motor. I need some help....
I have worked on Canons, Ricohs, Panasonics, Hp, and Kyocera/copystars. My experience with them all the Kyocera models are the best to service. Ricohs are pigs machines. I would go Kyocera do to call...
Found the Problem wasn't Hard Drive connector for the Drum unit wasn't seated in correctly. Machine is running!
I have a Savin 4051sp that is giving some issues. Machine come to ready really quick, No Please wait for fuser to heat up, But after one copy the machine stays in Please Wait Forever never going back...
I have an 1820 in a customers office that's having issues. When feeding the first copy after sitting 10 minutes ideal comes out with the image 3 inches pushed down. Once it starts coping again the...
I have had this issue before. Take the whole Toner Supply section off. Once you have done that, take the grey cover of the Toner Supply. There are sensors which need to be cleaned do too toner or...
Sweet Thanks I am going to the account today I will tell yea if it works. Thanks again for the advice!
I have a 255c that squeaks loudly. I have never heard it when running the copier. The customer calls the Office and says it's Squeaking when its Idle. I thought fans but all are run quiet but then I...
I had too travel over 60 miles cause a Copier was had lines, We called them and ask "Did you clean the slit glass?" They said "yes and it happens when it prints" I got there there was white out on...
Firmware fixs it. It did for me.
I am going too order the Stapler and try that. I will KYIF
I have been dealing with a Savin 8090 it has been throwing sc725 code for the last 2 months. I rest the machine and right off the bat I get a R jam, Open up the finisher door close it and get the...
Nothing would give me great pleasure to sell them a new copier. Working at a school print shop and they are Hurting as well, that option has been traveled. I have had this machine working in the last...
Hello Fellow Techs I need some help. I have been working on 8090 for the last year on and off again. Every time the machine duplexes, or collates a job the machine has small dog ears on the corner of...
I like to telling the new lazy techs when they ask "HEY WHATS THE PART NUMBER THAT I NEED??" I tell them " It's ID TEN T and to go tell it too the Parts guy". So they go to the parts guy and say "I...
Did you by chance clean the mirrors in the optics?
Because 1st copy is Internal it should come out good, But if the optics are all screwy you get it on your 2nd copy.
I am getting an error Message C7410. Once I turn on the machine it stays on the Please wait Screen for a minute or so, then it goes into a ready state. After that is show me a Error Code C7410. I...