Allan, I was wondering if you could elaborate on that forcing of a new article detection. I have the latest service manual for this machine and I don't see anything about it. Says engine sw 34 not...
Type: Posts; User: BR549
Allan, I was wondering if you could elaborate on that forcing of a new article detection. I have the latest service manual for this machine and I don't see anything about it. Says engine sw 34 not...
Sounds like you may have missed plugging a connector back in. The one that goes to the hopper empty sensor. Or, since these toner bottles have a chip in them, the machine knows whether or not you put...
How could you have been defrauded if it was free? Also, every time the machine is switched on, the life counter clicks away. Possibly also when coming to ready from sleep or low power mode. When I...
Have you tried enabling silent mode with engine FW dipswitch 37? You can do that on the C3350i.
Toner save mode is in the driver under preferences, quality tab. Also I've had to replace or clean the printhead sometimes on these to get it to darken up.
Thanks! I didn't know that. I'm definitely gonna look that up right now.
Well the T4 paper feed assy fixed it. Something was changed on it since the part # was updated to end with 11.
[QUOTE=DAR;2468465]
No skid marks. I tightened the door latch. I'll try pushing the door tighter. I ordered a T4 feed unit. Thanks.
Yes, I've been seeing this quite a bit lately. I too have had success with tightening the door latch pressure, but not today. I also have fixed it by cleaning the vertical feed rollers, but then they...
Yes I've had this problem before on a 28e. Definitely the printhead (LED strip). I didn't think replacing it was that bad. Easier than replacing a printhead on most other smaller machines. Replaced...
No. We were using only OEM toner. Kyocera says it’s caused by not shaking the toner bottle enough before installing it.
I ran into this a lot back when we had a lot of these out. All I did was replace the fuser and upgrade the firmware and didn't have any more issues. But as old as these are now, I would follow...
Replace fuser. It's a very common issue with these.
Well it was the toner supply unit. After calling Kyocera tech support twice about this and they tell me they don't know anything about it, my coworker found a service bulletin on it, 2R4-0030 (I155)....
It's not a brief sound. It makes the sound the whole time it's printing. I've got the transfer motor out along with the gears that are mounted to it. The noise is not there. I haven't seen a crack...
I have 3 of these in my shop doing this. 2 306ci's and 1 307ci. It's coming from the transfer belt drive. I can remove the transfer belt and turn the belt drive gear in the machine and hear the...
Does anyone know how to disable life stop for the IU on the 4752? Thanks.
Replacing tray 2 solenoid fixed it. The network cable was connected when he was booting up so, it must have been trying to print from tray 3 and tray 2 would feed the labels it had loaded at the same...
Feeds paper from both trays during boot up or printing. Both trays meaning trays 2 and 3. No paper in bypass tray. Put another M602 on top of the extra tray and it works fine. Removed feed rollers...
I posted the whole document already. The attachments are only enlarged pics of the same pics.
I got it from the Konica web site here in the US.
Have you tried this? I had a C360i this morning that kept getting stuck at about 25% on the boot up progress bar while I was trying to upgrade to B5. I did this and it's doing much better so far.
...
We use OEM rollers. We had lots of problems with Katun rollers about 10-15 years ago. We were replacing clutches, 1 way bearings, torque limiters and sensors before we figured out it was the Katun...
They know how to do it from in front of the machine. The customer that wants to do it is not in the same city as the machine. Trying to do it from webpage. I don't think remote panel is available on...
Does anyone know if there is a way to reset the account track totals remotely? It doesn't appear on the web page. Didn't know if any utility allows it. Thanks.