Search:

Type: Posts; User: NorthW

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    2,007

    Re: Canon ImagePress C700

    the PG-PICK number will be the tray selected, ie: 1= cassette 1, must have paper loaded for the test to run.
    most likely the ITB belt is worn causing the color registration to fail.
  2. Replies
    3
    Views
    1,806

    Re: IR6075 dumping waste toner

    You must check the waste toner main drive which is mounted in the back of the machine.
    That will be your culprit.
  3. Replies
    9
    Views
    2,544

    Re: c6010s jam code 0112

    My bad, that transport assembly kind of sticks out of the machine when the two halves are separated for shipping, could it possibly have been knocked during transport, so it isn't in correct...
  4. Replies
    9
    Views
    2,544

    Re: c6010s jam code 0112

    Maybe a broken wire in that fuser guide assembly, is that sensor in the guide that flips up when clearing a jam? I remember the yellow fuser cover catching the wire loom at the top if not careful...
  5. Replies
    10
    Views
    6,027

    Re: Canon Imagerunner C5045i weird print issue

    Don't forget to clean/ vac the external secondary transfer roller, that also can get covered in excess toner too.
  6. Replies
    18
    Views
    6,170

    Re: C7010 Registration/PCB 1-1 Memory

    If that's the case take a good look at the drive gears, bearing's, on the developer rail assembly, one of them is also a one way gear.
  7. Replies
    7
    Views
    3,494

    Re: Ir adv c9075 showing error e 075-002

    The white mark, patch, is on the inside of the itb belt. It does become soiled over time, inspect, clean if necessary, or replace belt. When you reinstall the belt the patch should be at the top.
  8. Replies
    18
    Views
    6,170

    Re: C7010 Registration/PCB 1-1 Memory

    Looking at your first attachment you were missing magenta registration marks on the front side, check that your developer unit isn't missing magenta starter on the dev roller and/or the unit is...
  9. Replies
    6
    Views
    1,440

    Re: IRA-8095 FM30 location

    I might be wrong but there are fans right hand side when you open the front door of the copier, I replaced a hopper once and left that connector off, it threw a fan error, but due to old age don't...
  10. Replies
    11
    Views
    6,983

    Re: IR5050 reset unit 1

    Can I ask if its a creaking noise/sound while in standby?
    The fuser roller bushings will be the culprit, need to put some of that magic fuser grease under and around them.
  11. Replies
    23
    Views
    2,266

    [Misc] Re: Help with IRA C7260 Network setup

    If Fiery.1 doesn't work, leave the password field blank, try that, failing that its been changed by some knucklehead and you will need system disk to reinstall system software on the rip. Double...
  12. Replies
    7
    Views
    8,079

    Re: Help on colorqube 8570 91,720 error

    Could one of the ink bars be stuck against the drum causing it not to rotate?
  13. Replies
    2
    Views
    4,781

    Re: Canon IR ADV C9060pro - e000197-0008 Error

    First easy step is to verify you have power to the multideck, it has its own power cord that could get unplugged by accident. If it has been unplugged, a simple reboot of the machine will clear...
  14. Replies
    4
    Views
    1,664

    Re: IR ADV 6055 jamcode 0103 -ps24

    Is that sheet on the wrong side of that black diverter??
    Do all other trays, 2,3,4 feed OK, duplex as also?
  15. Re: C203 with hash marks :::: :::: :::: black only

    I worked on a competitor's color machine and had similar fault, the itb drive roller was soiled and it caused dash like image on all colors, not sure how KM works but ya never know
  16. Replies
    10
    Views
    1,790

    [Misc] Re: C6000 with punch reg problem

    You mentioned the drive belt was loose, have you been able to tighten the tension for the belt?, maybe its as simple as that.
  17. Replies
    6
    Views
    1,894

    Re: Inbuilt calibration not finishing c7055

    Are you also using the Tiffen scale sheet that comes with the Fiery?
  18. Replies
    10
    Views
    1,512

    Re: Poor Color Prints on heavy paper

    You can adjust secondary transfer settings for heavy paper in service mode, HV-TR, give that a try.
  19. Replies
    6
    Views
    3,446

    Re: Canon Booklet Trimmer D1

    Firstly need to see what jam code the machine is giving, to eliminate the Fiery do a copy job with a cover and see what happens. Good you have the service manual for the fore edge trimmer too.
  20. Replies
    6
    Views
    3,446

    Re: Canon Booklet Trimmer D1

    Your infeed belts maybe slipping, get a magic marker and mark each belt in same spot and run a few books, not the job that's jamming. Then check the position of those belt marks again. You can try to...
  21. [Misc] Re: Ir-a-8595 copying issue from document feeder

    My bad, read your post in error, re: F4R, in service mode.
  22. [Misc] Re: Ir-a-8595 copying issue from document feeder

    You don't want it to AUTO detect size, use F4R setting in service mode, feed the original landscape orientation, and you select the feed tray where you setup that custom size. Maybe set up manual...
  23. [Misc] Re: Ir-a-8595 copying issue from document feeder

    When you place your document in the feeder what size is detected on the control panel?
  24. Replies
    15
    Views
    2,012

    [Misc] Re: Canon ir-c2880 // No network Connectivity

    If you know how to access service mode do an MMI clear, reboot. Cross fingers
  25. Replies
    42
    Views
    12,695

    [Error Code] Re: iPRC7000VP E020-0281

    Seems the engine is looking for fan rotation of fan that have been removed for the air kit, check the instructions again, there must be a necessary change made to a service bit switch in service mode.
Results 1 to 25 of 55
Page 1 of 3 1 2 3