Search:

Type: Posts; User: Rudi

Page 1 of 11 1 2 3 4

Search: Search took 0.04 seconds.

  1. [Misc] Re: Need advice with what copier brand I should purchase.

    I fully agree. We (Konica Minolta) have 20 000 more machines in the field than our closest competitor according to a recent survey that was done.
  2. Replies
    6
    Views
    696

    Re: xerox 510dp or océ TDS600

    Don't know much about the 510 DP except that it's in line with the 3050 the 8142 and the 6204 that's a good line( almost like a breed).
  3. Replies
    1
    Views
    538

    7120,7535 Ethernet ports are dead

    Hi guys, in the past 3 months i came across 2 7535's and a 7120 that suffered power surges. The only fault that occurred on all 3 machines was the ethernet ports were no longer working. Does any one...
  4. [Dead] Re: konica minolta bh211 Machine powers on then cuts out!!

    If you take off the cover where the paper exits on and look right at the back you will find a small board with a relay on, try that if all else fails. BTW, i am referring to a B210, but i am sure it...
  5. Thread: BH 161F purchase

    by Rudi
    Replies
    7
    Views
    645

    Re: BH 161F purchase

    Only if you dont want repeat business you should sell it to him.
  6. Replies
    174
    Views
    13,041

    Re: Hey folks, you remember common sense?

    In our country they introduced a new law with a very strict criteria that must be met to become a gun owner. As sad is it may sound, i much rather read the news paper headline of a sick individual...
  7. Replies
    2
    Views
    561

    Re: Xerox Workcentre 4150 enabler. What is this?

    It is a slot that is used at installion. a card comes with the machine and during set up you slide it in and remove it, very much like our other machines where you use a code to enable the machine.
  8. Thread: new to xerox

    by Rudi
    Replies
    6
    Views
    1,111

    Re: new to xerox

    Like most other companies, its the common sense that does the work. Most of the xerox training can be done on your PWS, wich i personally think is exellent cause monday i have to go and service a...
  9. Thread: new to xerox

    by Rudi
    Replies
    6
    Views
    1,111

    Re: new to xerox

    Hi, well i worked for konica minolta for just over 17 years and moved over to xerox about 2 years ago. It is quite tough getting to know the xerox machines if you havent grown up with them. In my...
  10. Replies
    2
    Views
    576

    X700 counting color for black

    Hi guys, our client has a X700 with a stand alone creo. When printing any 2 sised document e.g word, pdf, ect of wich one side is color and the other side black, the machine counts for 2 color...
  11. Replies
    0
    Views
    554

    Power supply for creo

    Hi guys
    I have a dc252 with creo bustled on the back of the machine. The creo's power supply went bust so i was wondering is there anyway one can maybe use an alternative power supply like say one...
  12. Replies
    0
    Views
    772

    Phaser 7400dn printing slow

    Hi guys , We have a phaser 7400dn that prints extremely slow when printing from tray 2 .The paper comes out very slow we have checked all motors .When we print from tray 1 mpt the speed is normal ,it...
  13. Replies
    1
    Views
    1,308

    Yes they are the same , 16 ppm and everything...

    Yes they are the same , 16 ppm and everything extra on the machine like fax and scan you have to buy ,i think this model prints through usb and parallel and i know it cannot be fitted with a duplex...
  14. Its normally eight zeros.If not, then it has been...

    Its normally eight zeros.If not, then it has been changed then you really have a problem.
  15. Replies
    6
    Views
    1,572

    Try holding in the utility key while switching on...

    Try holding in the utility key while switching on the machine , if it gives you a trouble reset option then press st00st01 , sometimes you can enter service mode that way , else you have to replace...
  16. Replies
    9
    Views
    939

    Welcome aboard , we certainly need someone like...

    Welcome aboard , we certainly need someone like you around.
  17. And it took us 25 years to find you. Hope you...

    And it took us 25 years to find you. Hope you have a wonderful stay .Enjoy!!! and welcome.
  18. Thread: Kindergarten

    by Rudi
    Replies
    38
    Views
    4,460

    Thanks alot for that tip , since december is...

    Thanks alot for that tip , since december is around the corner and africa is well known for its heat that will sure come in handy.
  19. Replies
    14
    Views
    1,488

    You go boy , i Had to try and get some brains...

    You go boy , i Had to try and get some brains into my 18 year old last night cause he is busy with high school exams. I wish it can get it over and done with cause am done stressing about this...
  20. Thread: DUPLO DP-430

    by Rudi
    Replies
    2
    Views
    3,394

    (6) "E006" is displayed Cause/Detective...

    (6) "E006" is displayed

    Cause/Detective section Procedures Items to be checked Result Countermeasure

    1 Does contact pressure motor turn when
    it is checked using HELP02*?
    YES Follow the...
  21. Replies
    13
    Views
    1,699

    [Misc] Since it was shipped, i would rather first check...

    Since it was shipped, i would rather first check the scanner. The shipping company might have tied it down a little too hard on the scanner in order to keep it stable. Give it a little upward twist ,...
  22. Replies
    5
    Views
    1,329

    i HAd to take check connections on pwb-a a couple...

    i HAd to take check connections on pwb-a a couple of times and also got paper fluff between the gears that drives the feed rollers, aspeciallly the big white one that sits in the middle of the other...
  23. Thread: Di470

    by Rudi
    Replies
    2
    Views
    894

    Could be a problem with the atdc control , run f8...

    Could be a problem with the atdc control , run f8 and see what happens.
  24. Replies
    1
    Views
    3,294

    [Error Code] Try this meter count stop 00 stop 01 3 start 3...

    Try this meter count stop 00 stop 01 3 start 3 start clear start. Dont know if this is 100% correct but it is as far as i can remember.
  25. Replies
    4
    Views
    1,285

    LOL !!!! Thanks for the nice tip connecticcut.

    LOL !!!!
    Thanks for the nice tip connecticcut.
Results 1 to 25 of 257
Page 1 of 11 1 2 3 4