Search:

Hi Thanks for the Colour CR5 Handy Guide does anyone have a Handy Guide for the CR5 Mono machines?

And you will need OCR as well and not that critical but e-manual as well just make sure you hard disk is the same size or large than the current disk.


Sent from my iPad using Tapatalk

Please check that your date and time are set correctly. I have that in the past the date and time are used somehow in the authetication.


Sent from my iPad using Tapatalk

Ok, thanks. I forgot that model range is actually a Lexmark machine, so all the Sharp functionality will not work

Sent from my SM-A715F using Tapatalk

Hi, you can use sharpdesk mobile to print from android phone. Ad long as the cellphone is on the same network as the printer. Please see link to the app on the playstore

Sharpdesk Mobile - Apps on...

Hi there what i have seen is that the primary transfer belt the tension is not enough the main spings need to be tensioned or posably change the primary belt unit with a new one there was a technical...

Hi there I have seen errors like this caused by Generic toners where the toner chip is faulty.

Here is another report that i found regarding Waste toner not installed properly

Hi check this technical report
this can be the problem that the waste toner box is not installed properly so the toner cannot get out of the toner spiral

The developer on this range of machine should never need to be replaced as it renews with each new toner cartridge has some developer in it, the other parts should be replaced at thier end of life as...

Hi check that the destination of the machine is set correctly as some destinations do not have osa as standard it is an option crop code 26-6


Sent from my iPad using Tapatalk

That machine has a separate NIC board AR-NB7 replace that and see if the machine is ok.


Sent from my iPad using Tapatalk

Hi there one small tip check that the copier is not connected to a switch with POE as sharp copiers do strange things when connected to POE switch. If it is connected to POE switch change setting on...

Hi the latest that I can see from my dealer is version 302
57153

HI the firmware of the MX-M266 with harddisk is different to the firmware without harddisk the sd card is also different

Hi 25-01 it used to mix the toner and dev then after that you run 25-02 to set the reference value.

Sent from my SM-A715F using Tapatalk

What I have found is just under the door cover is a metal spring plate that gets bent then it will show the door open when it is not.

Sent from my SM-A715F using Tapatalk

I think that your problem is that the toners where installed before running Crop 25-02 now you have to much toner in the Developer 25-02 sets the reference level try running 25-01 a few times without...

Thanks I know with older machine you just take the option rom out then set the dip switch to boot from sd card and install the original firmware in recovery mode and it works but this machine is...

Hi there I would like to know if this security kit can be removed from this machine?

Yes we also had this fault 4 machines CR4.5 colour and BW (non OEM toner all units) toner motor unit, crumb chip harness and PCU Pwb had to be replaced of cause toner supplier say never seen this...

hi there I know this is to late to assist you but this may assist someone else with the same fault I found this answer on a technical forum.




Model:
MX2630N, MX2651, MX3050N, MX3050V,...

There was an issue the the belt meandering there is a new belt unit MX-600FB the belt is a different shape so it comes with the input guide and cleaner blade that should be replaced your sensor maybe...

I discovered the fault POD1 sensor on the top of the fuser unit was faulty tried cleaning worked for a day then the error came back replaced it now ok.


Sent from my iPad using Tapatalk

Hi I have a machine with this code but all paper path sensor are ok and no paper in the machine.

Can anyone assist with this error?


Sent from my iPad using Tapatalk