you can use one of these, it costs very little, and I saw here on the forum everyone is very enthusiastic, then, for the smartphone, you download the ricoh connector or mopria print app, and you...
Type: Posts; User: luca72
you can use one of these, it costs very little, and I saw here on the forum everyone is very enthusiastic, then, for the smartphone, you download the ricoh connector or mopria print app, and you...
so, without jamming codes, the only thing I could think of that gives you problems is the worn/soft "gathering roller" (30 euros), if that's the case you can still remove it with soap and water and...
try taking a look at the "PM counter status" printout in the main SP menu, you will have a precise x-ray of what needs to be replaced, on such a small machine it is better to change the entire pcdus...
No Number, its in sp main menu, One last voice, called [PM COUNTER STATUS]
At Eye seem of yes, but you can check from you self if you print the PM status from sp menu, so you can see the pcu Life status
perhaps when you tear down the pick up station, you left a connector unplugged behind the vertical plastic cover, perhaps a tangle was hidden, and you didn't see it
I didn't read correctly that you needed information for the issue of serial number vs controller, yes, you must necessarily match the serial numbers from sp, otherwise it will give you sc995-01.
maybe there could be a problem with the mobile shutter of the id sensors that doesn't open correctly, try to check it, it seems to me that it doesn't have hp sensors, so I think it can also be...
it could be, starting from the simplest things, dirty optics, dirty ID sensors, an exhausted/too worn drum, or a cut on the ITB belt
to then move on to a failure of one of the 3 ID sensors,...
iin the service manual, there is a paragraph on that, (672).. there are additional procedures, and flow diagrams that I think are quite precise, I don't remember but perhaps on that model there are...
this is "solenoid week", a few days ago, another one also solved a problem caused by these
for the grinding noise, remove the front plastic cover of the ITB unit (2 screws) and locate the front black plastic cam of the ITB unit, now with a piece of paper in the front panel actuator,...
never happened, I really struggled, this is what I found, this is bad code.
-if you have one, I would try another finisher
-clean and lubricate the stappler unit axle (sometimes the overload make...
I've never heard of them here, maybe it's new(?)
could be...well, at this step, I would try as much as possible to disconnect all the user loads, motors, etc. from the IOB, and see if the sc changes, and then reconnect them one at a time, perhaps...
yes, it works, I mounted a 2003 on a 3003, but I wouldn't generalize about all models, I don't trust it very much, for example, two weeks ago, I had a 3004 here that didn't fix the toner to the edges...
SC665-08: comunication error from IOB signal.
it could be the PSU that is not powering the IOB board well, look on the attached PtoP for the power connector between the PSU and the IOB and check...
perhaps she was menstruating that day
I would try to start the machine with firmware from the SD card in slot 2, it should work, but I can't guarantee it, it has never happened to me on that model
its a "senior user"...LOL;)
I have never changed it, however you necessarily have to remove the complete door (quite a boring job) after which you can remove the complete by-pass unit (2 screws on the side, and 1 connector),...
what accessory do you use? spdf or rdf?...it seems like something crooked/badly assembled, also try to check that under the carriage, some anti-friction plastic thicknesses have not been lost, the...
I would also have bet me too on the registration clutch!...they are undersized, and I changed one recently on that model
Thanks, this Is a Quick operation👍
have you tried replacing the contact thermistors, I had a similar problem months ago, and I solved it like this, I tend to think that the fact of having to modify the working temperatures via sp is...