Search:

Type: Posts; User: itchyfinger@att.net

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: copystar cs 3050 trouble clearing grey background

    the pm cycle is 400k on the cs3050. depending on how long ago they had pm time may have shortened the life of drum and dev. we never ever use non oem toner in our machines. if I recall the toner...
  2. Replies
    18
    Views
    39,779

    Re: Going rate for mileage

    i drive my own car. 2016 ford flex. my company gives each tech a company credit card that covers gas, maintenance, and tires. no complaints here
  3. Re: Kyocera 4052ci manual toner door release

    you can also pull the cover off next to the black toner to the right and move the selonid by hand
  4. Replies
    3
    Views
    963

    Re: CS 4052ci color printing

    fixed it person says they did not have print server. come to find out someone send a wirless print to copier, but status shows nothing in the que. after we found and deleted it then some prints...
  5. Replies
    3
    Views
    963

    CS 4052ci color printing

    hello all, have a 4052 that when one of the colors run out it shuts down the unit. we have it set to print blk/white if color runs out. has current firmware. tried both restart and 906 via KFS. ...
  6. Replies
    8
    Views
    3,013

    Re: 3550ci J6000

    I had a unit do this same thing. replaced the feed tires in the cassette and have not had the problem since then. check 251 and if they have over 70 k replace them think it was a timing issue...
  7. Replies
    10
    Views
    5,120

    Re: Kyocera 5052ci print issues

    also try the current driver
  8. [CQ] Re: 356ci new machine, Magenta everywhere!

    any codes? maybe reseat magenta laser j connectors?
  9. Replies
    12
    Views
    2,185

    noise

    have CS6002 that makes a grumbling noise when ever it comes out of sleep mode of fired up in morning. unit has current firmware, new style bridge unit in the pf unit and fuser replaced as well as...
  10. Replies
    5
    Views
    1,836

    [Misc] Re: noise in fuser

    It can be hard to tell if the fuser or the exit assm is the problem. We have replaced both in units only to have the noise return. Finally I just started to oil every shaft, bushing and idler gear...
  11. Replies
    4
    Views
    1,108

    noise

    hello all, we the only dealer or have other dealers been having squeaking noises from the 02 series? we have put several exit assm and fusers in the units and they only last a month or 2, then...
  12. Replies
    12
    Views
    3,784

    Re: task alfa 4551ci print quality

    make sure you using updated drivers and current firmware. Go through and make calibration, tone curve adj and ect. And see what effect it dose for you
  13. Replies
    11
    Views
    2,039

    Re: km -1635

    oh ya jam codes and c codes would help maybe a 906 reboot
  14. Re: ECOSY M6030 cdn with 1 inch colour bands

    did you pull it apart and look at the drums? seeing a lot of the units with cleaning blades not cleaning properly
  15. Replies
    10
    Views
    2,142

    Re: kyocera color printers

    look at the 307ci Copystar so far we have had great luck
  16. Replies
    2
    Views
    877

    CS 306ci-CS456ci hash marks

    Hello, Still have not found a solution to the HASH MARKS in the K drum only. unit is at current firmware, have replace drum and developer together. Bulletin pertaining to sim 100 is set to 1. ...
  17. Re: TASKalfa 3051ci developer or drum issue

    agreed dirty charge roller clean all 4 of them while your in there and vacuum out the cavity. if you see blisters in the roller while cleaning it, replace it with the new style.
  18. Replies
    3
    Views
    898

    Re: CS-4035, Fuser issues...

    firmware is always important. go in to sims and reset 163 1nd 167 I believe. this will reset the counter for the fuser and should reset the 6000 codes. is it doesn't make sure you have good...
  19. Re: Riso GR image banding/noise at intervals on side of prints (in master)

    I would think impression roller or pressure. you say if switch drums it follows because its the master..I would try making a new master on each machine and see if it is the same on both machines. ...
  20. Replies
    3
    Views
    2,312

    Re: Uneven ink coverage on RZ970E

    its been a while since I worked on both A B Dick and Rizo digital dups. Make sure your impression roller is clean. any buil;d up or groves can cause this as well as the ink knife being plugged in...
  21. Replies
    2
    Views
    891

    Re: Lines on prints

    check your waste toner coming out of the transfer belt and to the bottle.
  22. Replies
    8
    Views
    1,535

    Re: Km5050 eject switch location?

    look on page 266 of the service manual, item 24 its in the eject assy.
  23. Replies
    4
    Views
    992

    Re: CS3050ci scan issue

    went out there today and reflashed the firmware. checked all the settings in the machine for forwarding and they are turned off. had customers it guy check their outgoing email setting and...
  24. Replies
    4
    Views
    992

    CS3050ci scan issue

    Hi guys, have customer that has one person in the address book that when he scans to email my boss also gets a copy of that email. have looked at the send/forward setting and it is turned off as...
  25. [Misc] Re: Kyocera 306ci What is the difference between a Firmware pack and Firmware turbo p

    it has been my opinion to use the full version instead of the turbo. you rewrite the whole version and not have any problems this way
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4