How many copies on this unit color, and black. I do not suggest to replace the DV unit. The unit is not a very common cause of DV push. I think that is a waste of money to ddo, but your call. I...
Type: Posts; User: Luke123
How many copies on this unit color, and black. I do not suggest to replace the DV unit. The unit is not a very common cause of DV push. I think that is a waste of money to ddo, but your call. I...
The reason replacing the MFP did not work, and doing the PCU won't work, is because the information is on the EEPROM's. If you can get onto the web page, then see if you can get to the service web...
There is not list of all the engine soft switch setting. For security reasons Sharp will not give this information out. They only give out soft switch info if it will help the machine. If you want to...
It seems that the paper just dies in the fuser, and no jam code, then my question is have you don a color calibration? you may have an ID sensor issue for color. You may uncover this when you do a...
copiertec is correct. You can only clear a U2 code with sim 16. I agree you will need to contact Sharp on this issue. I agree your issue is an EEPROM issue, and you will may need to get new EEPROM's....
These finishers are not that bad. Just need to learn them, and you will be good. I suggest to order the Disposition tray section 2 assembly. You can try to re-time it, but that is not an easy task to...
One thing you can try, is put the machine in a CN update. if the screen comes on, then not your ops, or the LVDS pwb. Since you did the SATA, then the next step is the MFP/SCN PWB. good luck.
You should be able to switch the base. i would reccommend that you look at the parts manual and verify that the ATC sensor for the black and magenta are the same. if not hten swap that too.
In my experience, One thing that should be checked before doing anything, go into CN update, and if the operations panel comes on, than you know the panel is ok. If the panel is blank in CN update,...
Sharp has removed 24-6, because resetting the meter to zero is the same as resetting your odometer to zero in your car. This is a bad idea to do. I do know a way to do it, but I can not tell you,...
First question I have, is have you verified the image on the primary transfer belt is good? Also do not start to pull the springs longer first. I suggest to look at the are front and rear that move...
I agree, and think you should try a new DV unit. As for the Calibration not showing up, You may want to look at SIM 26-53, and 54. That may give you some insight on that.
Just a couple things to look for if the problem returns. If the filters on the Dv units are small one, then I suggest you replace them with the large ones, and then do a full maintenance with drums,...
if the problem comes back I would agree with Spanky it is time to replace the DV units.They have a lot on copies on them. Have you also checked to see the amount of toner the customer is using on the...
What is the problem you are having. If you need a new SD Card, just order one. You can also try a CN update. That can sometimes bring back the SD card.
Search this on on the Forums
admin login lost
Did you do sim 30-1 before just ordering sensors. That may lead you to the sensor. It can also help you look beyand the sensor, and to a board issue. Just seems like more troubelshooting is needed.
You need to look very closely on the MFP PWB for a small black box that has 2 dip switches in it. Once you find it, and with the copier off move the left dip switch up, and turn on the copier. once...
Here are 2 ideas. 1. Try to upload a fresh blank clone. 2. If the clone does not work, then try a end of lease. I suggest to backup all customer data, but do not re-upload it untill you have...
If your getting this on several machines, and after a PM, then the developer units are not being clean well enough. I would double check the method that is being used to clean the dv units on the...
Have you looked to see if you have anything stuck at the dv doctor blade?
This sensor gets its reading from the black fold roller. Have you tried cleaning this roller with soapy water really well. The roller will get a grey haze, and can cause the sensor not to read well...