Thank You!
One simple adjustment (PRCS-ALG: Adjust the width of process tray align plate) fixed it.
Type: Posts; User: pmailfl
Thank You!
One simple adjustment (PRCS-ALG: Adjust the width of process tray align plate) fixed it.
I have 2 identical C9075's with booklet finisher. On one of them, paper started spitting out slanted, sideways, and won't stack properly. After a few sheets come out and the unit continues to spit...
There is 2 feet of space behind each printer, they are all on dedicated lines. My warehouse is climate controlled, 24/7. It never gets above 78 or below 65. As far as where it's stored before it got...
Extremely frustrated --
2 C9075's and I'm constantly running into issues where it is impossible to have both of these up and running at the same time. One machine has 2.6 mil, the other 600k. On...
I measured the voltage across the two hots on a double-pole breaker. It is definitely 240 and the line is only going to be 10 feet from the panel, so it's not going to drop off that much. This is a...
The spec sheet says 208 +- %10, which will only put it at 228. My meter reads 241, so not taking any chances. Will either run a step-down to the machine or a bigger step-down to a sub-panel so I have...
I'm having a C9075 Pro installed this week, electrician is out here and the power is 240V Single phase. Canon literature calls for a 15amp 208V outlet. Does anyone know if the machine will run on 240...
DC_CON 20.21
R-Con 2.03
Panel 00.03
Feeder 4.01
Sorter 20.08
NIB 5.00
MN_Cont 77.03
Yes, the perfect binder is setup as 1, the finisher as 2, on system monitor when trying to print, it shows the devices in the correct order.
Not sure about firmware or how to check.
My 7095 with V2 Saddle Stitcher worked fine.
Installed the Perfect Binder and when attempting to make a copy, the finisher constantly cycles, display on 7095 cycles back and forth between...
From tray one only, printer will print, pause and flash load paper, then continue, and pause again, over and over.
The entire tray assembly and rollers have been replaced, hard drive cleared, and...
I'm back to square one:
Checked all the fuses, replaced a blown fuse causing the error message. Now the machine fires up, the controller fires up, but the machine shuts down. No lights on the...
It's Menu, Up Key, And Enter Key, hold all 3 for 3 seconds.
I do not know the default password though.
Trying to set this up to see if it will run, I've got the is700c connected, when I power the machine up the display shows "Please Wait" then after a few seconds it powers off. The sleep or any other...
I have an HC5500, would like a reliable tech (preferably independent) to come set it up and maintain when necessary. Any recommendations, or anyone here work on these?
Most of my printing is text, and a lot of it through Word Mail Merge via the PCL driver on my Win7 machine. I use PS Mail for the complex jobs Word can't do, but that will only send postscript.
...
Ack. That's what I was afraid of. For now, I have an old box running XP for the sole purpose of being able to print PS from PrintShop Mail to the M1, but it is a PITA.
Perhaps next time I need a...
I've searched the canon site under Ir105 & ImagePass M1 and can only find PCL drivers.
I have the PS driver for XP, but it won't install under Win7 (either 32 or 64bit), can't share the printer,...
I am definitely staying with Canon, no question about that. Was just curious if the newer machines had the Trained Consumer Replaceable Units.
One other question:
When should the tech be called...
My problem with that is space and power.
Even if I had the room for an additional machine or two, I would need to install a sub-panel, since my electrical panel is maxed out (All the 110 slots are...
I purchased a 105 on ebay with 10 million impressions about 3 years ago and it has served me quite well. I am now approaching 13 mi on the meter and service calls are becoming more frequent.
My...
I am having this same problem, and do not care about scanning or copying right now.
Is there a way to "bypass" it until a tech gets out here so I can send print jobs to the machine through my...
Hi,
I am considering an IR 8500. It was a walk up printer in a shop nearby and has 4.5 million clicks with an almost new drum.
It's main purpose would be as a backup to my 105 and for doing...
Thank you to everyone for their help.
I called the tech and asked him to bring over the 3 corona discharge units, clutches and rollers for the trays. He changed it all out and the jams were gone...
I'll check that out, but it hasn't jammed from Tray 2, and I've run 600 sheets through it. I would test a long run, but the prints are not usable.
My biggest problem now is the lines on the...