Sounds like control board.
Sent from my SM-G930V using Tapatalk
Type: Posts; User: daileyrobn714
Sounds like control board.
Sent from my SM-G930V using Tapatalk
Do they use the bypass a lot? How many clicks? And like the other Tech says, check your paper settings.
Sent from my SM-G930V using Tapatalk
The last time I had that same problem, was a simple fix I change the roller.
Sent from my SM-G930V using Tapatalk
Sound like you need to update the firmware Watermark firmware
Sent from my SM-G930V using Tapatalk
yuuuup
Sent from my SM-G930V using Tapatalk
Check your mag roller in the DV unit ...somehow tiny fragments of metal get stuck to the mag roller and that will cause you avoid lines it's really difficult to get it out of there because it's...
Bottom right corner
Sent from my SM-G930V using Tapatalk
Tap the version twice, that will open up the keypad
Sent from my SM-G930V using Tapatalk
They do have a shelf life, but I've never seen them expire. I'm not experienced enough to troubleshoot, I actually need to be in front of the machine. But I am curious to what the issue actually is...
First I would check my developer unit, make sure the mag roller is completely covered and developer.
Sent from my SM-G930V using Tapatalk
There was a dent in my paper as well..found a issue with that mylar, that why I replaced it.
Sent from my SM-G930V using Tapatalk
I do apologize. that's what I am saying, I am not sure which one it was .I had the same problem pod-1 ... I changed EVERYTHING the helpful techs were suggesting fuser/fuser drive ect. nothing...
I do apologize if Iam making it confusing, I'm not sure exactly what the actual fix was... I replace both parts. sorry I am a new tech with little experience. [emoji848]
Sent from my SM-G930V...
Cfrm-1117ds53 transport unit. This is what I replace on the machine haven't had a problem since ran over thousands of copies
Sent from my SM-G930V using Tapatalk
Dunt-7302dszz Interface pass unit. This is the part that drops down on top of tray 1 when you pull out the tandem tray unit.
Sent from my SM-G930V using Tapatalk
your problem is in the drop down path over tray 1 the path comes together with another path sorry I am a new tech so I don't know the lingo.I had the same problem. l will look for the part # give me...
I get$ 300 a month for car allowance and $0.25 per mile after that. That's in California
Sent from my SM-G930V using Tapatalk
Loved all the responses endless possibilities. Simple solution. Lesson learned don't overthink it.
Sent from my SM-G930V using Tapatalk
It's funny you mention that, the rollers and tray one were bad I replaced them as well and so far so good. Thanks for all your help I do appreciate it
Sent from my SM-G930V using Tapatalk
Thank you very much !
Sent from my SM-G930V using Tapatalk
Hi guys, just reading over your comments. I'm wondering I'm having the same issue with my Sharp MX-B402 with constantly cleaning the transfer belt. I changed the transfer belt cleaned all sensors....
Hello everyone, I'm having problems with scan to network folder. I downloaded and installed the special firmware. I did it through simulation 49 - 1 I checked the firmware version it does get...
Wow! That is awesome. I love seeing that. Thank you
Sent from my SM-G930V using Tapatalk
Yes sir, never seen a sharp machine tell me it needed firmware. Interesting. If you go to Sharp indc you have to credentials to login
Sent from my SM-G930V using Tapatalk
Ok, thanks.oops I commented on the wrong model. Sorry about that.
Sent from my SM-G930V using Tapatalk