I had them put in a dehumidifier about a year ago. There’s honestly not many things I haven’t done.
Type: Posts; User: DSharpe
I had them put in a dehumidifier about a year ago. There’s honestly not many things I haven’t done.
This machine runs for a few months and then starts jamming like crazy. I was over there earlier today and ran approximately 2000 without any issue. Gone for a few hours and right back to jamming...
Has anyone ever swapped the mfps on the 8 series non e with another 8 series? I know the 4es you can do it but ive never done it on the 8 series. Thanks
Yeah this one only has a problem with the PC-410. It knows its there but will never even try to feed or lift.
Oh, knew about that board but didn't realize it had anything to do with the PC-410. I can take one as well to test before swapping the PRCB. Thanks for the info
Is it possible to swap the print control boards (PRCB) out from another machine without bricking the machine? Thanks guys
ive got a PC-410 under this machine and it will code sometimes with a...
We had a tech to go out to a kip 7100 that had 350k sf and he decided to do a complete pm on the machine. Drum, ts and charge wires, dv unit rebuild and fuser rebuild. We are getting some void areas...
I went ahead and updated the firmware in hopes that will take care of the issue. If not, i will look into resetting those chips. That will be a first for me.
3.25.7 CE301, CE302, CE303, CE304, CE305 (bizhub 558/458/368/308) (1) Contents Trouble type • CE301: Referring incorrect memory • CE302: Incorrect command • CE303: Finished due to error inside Qt...
Well, since ive posted this there has been a firmware update within the past few minutes that fixes this possible (E301) and a lot of other things. Will update you guys in a few days, as im...
Was hoping this wasnt going to be an issue issue on this model. Everything has been reseated, has latest firmware and diagnostic check come out fine. Machine is only a few weeks old. Good times!!
Ended up being the 2nd transfer section. I originally replaced it for that same problem. Had to adjust the spring pressure below the transfer roller itself. There is only one spring underneath the...
If you lift up the cover on top of the adf there is a switch on the front side for the open and closed state of the door. U can try reforming that metal to make more contact or replace the switch...
Its just plain paper. To me, it looks like its losing transfer. Same on prints and copies. What im getting at, KMBS is leaning toward PH Unit.
Whats up guys? Having an issue with a C3350 that prints fine then all of a sudden gets very faded. Ive replaced the entire transfer section, hv unit (the board was actually cracked so i knew when i...
I have replaced the mfp and the main control board. I can definitely see the laser being a possibility not sure about how the HDD could cause that? But then again, that’s why I’m looking for help...
The data is indeed missing in the void cross feed. If you notice the sheet on the bottom that void has actually moved a little more to the right of the page. The entire image is there with the...
Its always the same size and going from front to rear. The samples i have seen most of them are on the right side of the page but i have also seen it once on the other side. Its missing but neatly...
All that is fine. Machine has 112,000. Also, this is very intermittent when it happens. i had the machine in my shop and ran 6000 copies on it with no problem, after mfp and main control board was...
SAMPLE OF PROBLEM. Can be anything they are sending to the machine from emails, web pages or tax software.
HDD has not been replaced......yet.
Im going to run a powertronics monitor out there tomorrow and see whats up and just leave it a few days. Ill have her jot down the time on the issue if it shows it self and then go back to the...
The drum itself is fairly new and the machine has around 95k on it. The problem is that it may do it only one time and it may take a few weeks or more to show up. Totally random. Could be related...
Whats up guys? Working on a Bizhub 454e that randomly misses a 1" section of print at times. This has been an ongoing issue and the customer is a tax office so automatically equals good times...
Hey Guys, the black developer clutch did fix this issue! Thanks again