It's a negative, that's interesting. Thanks for sharing. How much confidence do you have in that solution? =^..^=
Type: Posts; User: blackcat4866
It's a negative, that's interesting. Thanks for sharing. How much confidence do you have in that solution? =^..^=
I like this one. Perhaps the shading adjustment cannot be successful because of direct sunlight into the scanner cavity.
On a tangent: I had a Mita many years back that was having continual...
The fans are there to cool various parts of the copier as they become hot. Yes, parts of the copier may become hot, even when you are not currently making prints or copies. You should not expect the...
Here's my theory, tell me what you think:
The color toners are layered onto the transfer belt in this order: first K, then C, then M, then Y. Black is always the first layer onto the transfer belt...
Based on my experience with roller separation systems, I would suggest that there is too much pressure set, pressing the separation roller to the feed roller.
I am not familiar with the specific...
Welcome!! =^..^=
I look forward to those conversations. =^..^=
Welcome! =^..^=
Mr. Synthohol would be very gullible if he handed out his logins to anyone that asked. I am hoping he's a little smarter than that. =^..^=
Most often, a piece of plastic breaks out of the rail on the right or left of the paper tray (ON the paper tray, not in the the machine). It's usually because somebody leaned on it while it was...
Did you clean the timing pulley on the carriage motor. I've seen the rubber shavings from the old belt pack into the grooves of the timing pulley, making it slip. I don't think that I've ever seen a...
Determine which drum fits too tightly on it's drum shaft. In my case it was 3 out of 4. Install only one drum, then close the drawer to see if it closes properly. Remove that drum, then try the next...
Could it be that it had a Lexmark toner cartridge installed, not a Toshiba cartridge? Or vice-versa? I'd think the EEPROM would be coded differently. The reset may have changed the manufacturer to...
There certainly isn't a lot of detail in that bulletin. It would have been nice to know what changed. Or would that be too much like admitting there was a problem? =^..^=
Your welcome. Sorry I missed your post on the first go-round. =^..^=
The cyan & magenta developing units are the only thing it needs..
Yes, I reduced the resolution on my camera phone so that the pictures were 1MB or less, then they upload just fine. =^..^=
Sorry, no DIY fix. Those developing units are glued together. I have tried disassembling a few units, but just ended up with broken plastic. The other machine would use the same spacers, but there...
The cyan and magenta developing spacers are bad. AFAIK the only way to get them is on a whole developing unit assembly. This was a common flaw on this series. =^..^=
This is a Lexmark rebadge. Check that the toner cartridge contact set is not broken or damaged. =^..^=
This is the one I thought of. WSD does not function reliably. Choose a static IP in the driver. =^..^=
Those rollers look VERY worn. I'd start there with new rollers. =^..^=
OMG. I can see why it's useless. It might work in an isolated situation where a printer is plugged directly to a laptop with a cat5 cable, without the benefit of DHCP it could choose an off-range IP....
The paper does not look like it is loaded properly. My suggestion is to:
* remove all the paper from tray #2
* perform a U906 partial reset to clear out the lift error.
* load a small amount of...
Hello Hans.
2000:0006256
You can disregard the part after the colon, that's the copy count.
C2000 is a main motor error (not rotating). Something is seized and won't allow it to turn, possibly...
I agree with this one. Konica Minolta CCDs that do very long scan runs are well known for failing on the 654e series, and 808 series. Usually they store errors that auto-reset, but come back more &...