Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds; generated 11 minute(s) ago.

  1. Replies
    5
    Views
    2,716

    Re: Accurio c2060 error c2221

    Determine which drum fits too tightly on it's drum shaft. In my case it was 3 out of 4. Install only one drum, then close the drawer to see if it closes properly. Remove that drum, then try the next...
  2. Re: Toshiba 385s invalid factory configuration problem

    Could it be that it had a Lexmark toner cartridge installed, not a Toshiba cartridge? Or vice-versa? I'd think the EEPROM would be coded differently. The reset may have changed the manufacturer to...
  3. Replies
    5
    Views
    413

    Re: Bizhub C250i poor fixing

    There certainly isn't a lot of detail in that bulletin. It would have been nice to know what changed. Or would that be too much like admitting there was a problem? =^..^=
  4. Replies
    9
    Views
    1,049

    Re: Calibration Toner-Banding on paper edge

    Your welcome. Sorry I missed your post on the first go-round. =^..^=
  5. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    The cyan & magenta developing units are the only thing it needs..

    Yes, I reduced the resolution on my camera phone so that the pictures were 1MB or less, then they upload just fine. =^..^=
  6. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    Sorry, no DIY fix. Those developing units are glued together. I have tried disassembling a few units, but just ended up with broken plastic. The other machine would use the same spacers, but there...
  7. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    The cyan and magenta developing spacers are bad. AFAIK the only way to get them is on a whole developing unit assembly. This was a common flaw on this series. =^..^=
  8. Re: Toshiba 385s invalid factory configuration problem

    This is a Lexmark rebadge. Check that the toner cartridge contact set is not broken or damaged. =^..^=
  9. Thread: Biz754

    by blackcat4866
    Replies
    6
    Views
    585

    Re: Biz754

    This is the one I thought of. WSD does not function reliably. Choose a static IP in the driver. =^..^=
  10. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    Those rollers look VERY worn. I'd start there with new rollers. =^..^=
  11. [Misc] Re: Printer APIPA IP question - Is this printer acting as a server?

    OMG. I can see why it's useless. It might work in an isolated situation where a printer is plugged directly to a laptop with a cat5 cable, without the benefit of DHCP it could choose an off-range IP....
  12. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    The paper does not look like it is loaded properly. My suggestion is to:
    * remove all the paper from tray #2
    * perform a U906 partial reset to clear out the lift error.
    * load a small amount of...
  13. Re: ECOSYS P2040dn showing Call Service 2000:0006256

    Hello Hans.
    2000:0006256
    You can disregard the part after the colon, that's the copy count.

    C2000 is a main motor error (not rotating). Something is seized and won't allow it to turn, possibly...
  14. Replies
    5
    Views
    568

    Re: C458 rainbow effect scanning

    I agree with this one. Konica Minolta CCDs that do very long scan runs are well known for failing on the 654e series, and 808 series. Usually they store errors that auto-reset, but come back more &...
  15. [Misc] Re: Printer APIPA IP question - Is this printer acting as a server?

    Just for us dummies: What is APIPA? =^..^=
  16. Replies
    6
    Views
    1,165

    Re: Opinion on Oneway Bearings

    I happen to agree with your strategy. =^..^=
  17. Replies
    4
    Views
    236

    Re: Présentation.

    Welcome! =^..^=
  18. Replies
    7
    Views
    695

    Re: Lost GED Certificate

    You are stuck following the process through to it's culmination. Anything else is a forgery. =^..^=
  19. Re: Why does wsd printing work then not work?

    Maybe I've got this wrong. Somebody please correct me if I do: WSD only connects with the printers during initialization. If the printer loses communication, or is not available during bootup of the...
  20. [Electrical] Re: TA 358ci Power surge.. now lines on prints

    Congratulations on your success!! =^..^=
  21. Replies
    4
    Views
    322

    Re: Hi guys. I'm newbie.

    You're in the right place for all of those things. Welcome!! =^..^=
  22. [Electrical] Re: TA 358ci Power surge.. now lines on prints

    If it's drum diameter, there is a chip in the coating of one (or more) of the drums. Take a known good DK-5195, and try it in each location, until you get images without the bands. =^..^=
  23. [Electrical] Re: TA 358ci Power surge.. now lines on prints

    What's the interval of repeating, in millimeters please?
  24. Re: Bizhub c454e ADF 4x6 stack scan // Getting stretched section on 1 of 4 prints or

    The only way this could possibly work is SEF (short edge feed), and with photos, yes you will have separation issues. The smallest acceptable original size per specifications is 4.92" x 6.93".

    You...
  25. Re: Lexmark/IBM Wheelwriter 3000 power supply

    I found a few whole typewriters on eBay, not too expensive. So far that's the only path forward. =^..^=
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4