A man takes a blow up doll back to the sex shop, and throws it on the counter!
"It's faulty" the man says to the shop keeper.
"Why... what's wrong with it?" asks the shop keeper.
"It has a...
Type: Posts; User: Lea@ABM
A man takes a blow up doll back to the sex shop, and throws it on the counter!
"It's faulty" the man says to the shop keeper.
"Why... what's wrong with it?" asks the shop keeper.
"It has a...
I had a message saying to replace Cyan, Magenta and Yellow printheads so I replaced them all with in-date, genuine HP ones, it run a head alignment and still keeps saying "ATTENTION REPLACE...
I have a customer with an OKI MC860 using original consumables and it will not reset the Y drum count. I have checked to see if the unit fuse has blown and the machine isn't blowing the reset fuse....
I have a customer with an OKI MC860 using original consumables and it will not reset the Y drum count.
I have checked to see if the unit fuse has blown and the machine isn't blowing the reset fuse....
Down the left hand side as you face the machine towards the rear, remove the little square panel where the scanner meets the machine there are a row of 4 or 5 screws. Loosen them all, lift the...
Press roller bushings and seps. I've also doubled up the sep springs before but it reduces the life of the top roller. Try a ream of better quality paper aswell.
Change the main black connector block on the rear of the fuser. It comes complete with wiring to the stats and lamp terminals, or if you have another machine, swop the complete fusers over and you...
I'm not 100% sure but I'm guessing the nearest you find that will fit is a 220/270 or 1022/1027 as they work at the same speed.
Can anybody help me??
I fitted a new OEM drum unit to a Xerox Workcentre Pro 421, presuming that it would just accept it and reset the machine but it still just sat there with the replace drum...
Thanks Eric, Just to let you know what it was, when I had replaced the feed belt in the past, the holder for the belt was put in upside down. Took it out, turned itt over and no problems since!...
Thanks to you all. Thought i would let you know, I changed the pressure roller and that fixed it!
Im struggling with a machine that keeps jamming as it exits the fuser.
It's very intermittant and I cant see anything obvious when it does it.
The lead edge of the paper seems to get about 2...
I had a machine that jammed just below the fuser exit sensor. After replacing the sensor and tearing off the solenoid cushions, it still jammed.
I finally fixed it by sliding out the fuser and...
I had a machine that jammed just below the fuser exit sensor. After replacing the sensor and tearing off the solenoid cushions, it still jammed.
I finally fixed it by sliding out the fuser and...
Thanks Eric, will try that. :)
Hi,
I have a 1027 that doesnt seperate properly throught the DF.
I have changed the pick up tyre, feed belt, sep roller, torque clutch and drive gear with the one-way bearing in it and...
I know this is an old post but I have a copier with exactly the same fault.
First 3 copies poor fusing, then ok until machine goes back to standby!
Have tried to follow the link to the bulletin...
Im no scientist but isnt it more environmentally friendly to use virgin paper than recycled?
More tree's are planted everyday due to the demand for paper that would not otherwise be on the planet...
Hey thanks for both of your replies. It was the optics adjustment like Totoro said.
I have had similar problems with 1045's but with those I just bend them back. A little crude I know but this...
Duh! In 1992 the SF8500 was a brand new machine! :rolleyes:
24 years. First training course was a Minolta EP300/RE when I was just 16! Self employed for 13 years since.:cool:
Seems like optical skew to me but checked mirrors and they are all in square.:confused:
Image is skewing in a parrallelogram effect. ie the image is out of square. Short edges are parrallel with...
Was servicing a Sharp SF8500 on a balcolny above a Porsche car showroom in Nottingham 1992ish.
Took out the full waste toner bottle which is tall and thin making it an unstable object even if it...
I know its and old discussion now but it's still worth mentioning:
I have tried using 1045 dev in 1015's and 1027's with no problem. (obviously measuring out the correct weight first :rolleyes:) ...
See this link: :)
http://www.copytechnet.com/forums/ricoh-savin-gestetner/8156-ricoh-1045-first-duplex-copy-jams.html