Search:

Type: Posts; User: EarthKmTech

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: PC417 Jams

    by EarthKmTech
    Replies
    10
    Views
    1,891

    Re: PC417 Jams

    I'm having a number of these trays all with the 1740 jam from tray 4, the accessory version and the standard version on C750i now, its not jamming or slipping on the paper. The actual transport motor...
  2. Re: Konica C224e - C364e series cyan dv units issue(and P.S. ads and popups on this s

    been using adblockers for years, hard to beleive people tolerate the number of ads out there these days. Youtube is the worst now, unwatchable without it.

    In addition to the mandatory duct...
  3. Replies
    7
    Views
    703

    Re: C308 connection conundrum

    if network settings initialised packet filtering is enabled by default (in my marketing region anyway) and if what you are connecting to it from is on a different IP range this will give you these...
  4. Re: Will Kon/Min ever make a fuser that don't make noise?

    Exit assy's are very common to squeak on the sparrow series, and also not hard to lube all points of friction with a suitable plastic compatible grease. Once done correctly its generally not an issue...
  5. Replies
    4
    Views
    1,244

    Re: C4050i DF Control Board

    I've seen near new SMD capacitors dead short after some time in operation. I've had other boards with this issue, including with vapourised tracks because the load wasn't enough to put the psu into...
  6. Replies
    10
    Views
    1,767

    [Misc] Re: Konica Minolta BizHub C300i

    had this a few times - if its not the sensor inside the front left (either contaminated or faulty) that is activated by the actuator rocking on the cam lobe on the side of the box, it is usually the...
  7. [Misc] Re: bizhub c4050i 5min warm up and paper not recognized

    this is always a TCR issue. Older firmware has the no paper recognised in the tray bug when the TCR abnormaility happens.

    Check TCR levels, guaranteed once of them is low.

    Usual issue on these...
  8. Replies
    11
    Views
    1,628

    Re: c454e mystery blue line?

    check cyan led erase array. If one LED is dead shorted (wired in series) and not illuminating, you will have a continuous ring of non erased garbage.
  9. Replies
    9
    Views
    1,064

    Re: c300i series drum edge damage

    C750i drums are notorious for squeaking.

    I've seen the black drum blade overheat and flips / stops cleaning properly on machines doing thousands of pages in a single run too. (c750i)
  10. Replies
    9
    Views
    1,064

    Re: c300i series drum edge damage

    This is exactly the issue, annoyingly, several machines have done it a second time and no mention is made of the lot number of when the pcr rubber composition changed. So we are just left to hope for...
  11. Replies
    9
    Views
    1,064

    c300i series drum edge damage

    I look after multiple remote locations and minesites - this one is equatorial and has 90+% humidity every day of the year with constant temperature that never changes. It is not at all dirty all...
  12. Replies
    10
    Views
    1,688

    [Misc] Re: FS-534 and FS-536

    It's not supported - but it does work. I have a C250i with FS-534SD at home, all functions work as expected.

    You must NEVER update the firmware with the unsupported FS-534 finisher plugged in or...
  13. Re: bizhub 4000p, seems I made a boat anchor....

    to use a used panel as a new one involves modifying the data stored on the serial eeprom on the panel board. Not rocket science but not in the scope of what a technician should be playing with.
  14. Replies
    11
    Views
    1,488

    [Jamming] Re: B758 B958 J-3205

    The standard things to check for this, including on the Colour versions of this engine, C659/C759

    1, ensure duplex gate lowest point is 34mm off the table when measured outside the machine ( no...
  15. Re: C3350i adf rollers that dont lock in upright position

    On the filthy minesites i look after, my above mentioned mod has been a hit. Every modified machine with lessened spring pressure on that stupid retaining hook has never had the issue again. I'm...
  16. Replies
    3
    Views
    6,605

    Re: OpenAPI App Manager name change?

    is this simply for removing stuck / old API installed from the machine? you have been able to do it at the control panel for some time now.
  17. Thread: TONER

    by EarthKmTech
    Replies
    8
    Views
    7,621

    Re: TONER

    don't be so sure about that... Nothing that large, only desktop's.
  18. Re: Issues making copies from platen glass. Bizhub 458

    Replace the flat bed scanner.

    Its actually a very easy task and takes me about 15 - 20 minutes with an electric screwdriver. I take photos of the scanner adjustments from the donor machine before...
  19. Replies
    7
    Views
    765

    Re: C458 ADF Left Cover Adjustment

    Yep +1 this

    Seen this plenty when people try lifting open the jam access door without unlatching it. This is a 100% fix.

    Also helps with the 6633 jams resulting from insufficient separation...
  20. C3350i adf rollers that dont lock in upright position

    Anyone else dealing with this?

    Replacing the pickup assy is a quick fix, though expensive and it only lasts a few thousand pages before it starts again.

    Trimming 4 loops off the hook spring...
  21. i series reduced color gamut in thick paper mode

    When printing smooth transitions from light to dark in any colour there is banding in any mode other than plain paper mode on all I series color.

    It matters not what driver is used, windows and...
  22. Replies
    10
    Views
    1,342

    Re: BizHub C227 color intensities

    Looks a lot like an end user.

    New account, first post, extremely basic issue.
  23. Re: Software Switch for scrapping a printer

    4 / 4e series remove and destroy ssd module
    8 series remove and destroy emmc module

    Older - remove and dispose carefully the nvram module (lithium battery caution)
  24. Re: i series warped registration units various jam codes 9901 2001 3003

    Print quality is miles better on the older engines too. People want to pay as little as possible for the machines though, so this is the end result.

    I saw an old c452 recently on a minesite full...
  25. Replies
    6
    Views
    675

    Re: c3110 new eBay purchase

    Hope you didnt pay much, most of these go to recycling with fairly low counts. Many were tossed in for free as sweeteners in multi large machine deals.

    They are kinda crap and have long and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4