I was able to replicate the freezing on the machine by sending large scanner or copy jobs to it. In the middle of those jobs the document feeder would stop/pause feeding two to three times in the job...
Type: Posts; User: Lawrence
I was able to replicate the freezing on the machine by sending large scanner or copy jobs to it. In the middle of those jobs the document feeder would stop/pause feeding two to three times in the job...
Howdy folks
Got a 3253 3.5 hours away that is randomly freezing up when doing scan to email. Its stuck on the scan screen during scanning the pages. Pic below. Apparently they can hit the...
Hey guys,
Does any body have a list of backwards compatibility for fusers and drums etc for M3550, M3640, P3140 etc.
When i first started with this company i had a call on a M3550 that needed a...
Im new to the Kyocera game but ive seen on that frame 4 things.
In the side door rear frame side near the top is a little white plastic roller, i think it's a belt tensioner.
In the LCT trays 3/4...
Had this error code today on a 6003. Customers power went on and off numerous times quickly before it finally kicked out for 6 hours.
It was strange, machine was offline (maybe power was still...
The bearing to the left of the green circle. We thought the grounding plate was making noise at first.
6079260793
The metal roller above the fusing belt that is part of the fuser unit. There are brown bushings and they wear down causing noise.
The metal rollers we saw were cut rough and they eat the bushing....
Replacing the transfer belt and transfer roller did resolve this.
Howdy folks,
Customer called in with a K eprom error. Power cycle cleared that but i noticed a defect in the prints. In high density blacks im getting a bleed out reaching for the lead edge. ...
Sorry to resurrect such a old post but did any of you guys ever find a solution to this? Unless i missed a post in this 14 page saga it looks like every body has tried everything with no luck. I...
I was hoping I'd see a answer from you :D
I did have the dv out. It wasn't Terribly dusted and I did wipe up around the reg but I didn't check the paper dust cleaner.
Could that cause first...
Howdy folks
Working on a 7002. When printing a status page i get a mark on the back side of the page. If i run a font page only the first page has the mark and the following pages are clean. ...
We replaced the main motor in the DF on a machine we just installed and it died during demo. They do fail!
If you order the board don't forget the DF white calibration sheet Adjustment 14A2.
The packing it comes with is stupid huge. Box in a box. We take the smaller box out and just put a sticker on with the part number.
The 5503 fuser was pretty quick to rebuild but the 6004 and IM...
In Canada its $20 cheaper to replace the entire fusing unit vs a sleeve and pressure roller never mind the time of the lazy tech :p
Just had a IM C6000 do this. I replaced this fuser 2 months ago and it's howling at 52k. I think Ricoh has a manufacturing defect.
Howdy folks
Got a MP 4055 with the large capacity tray under the machine which is Tray 3 throwing J012 jams.
When it does jam the paper is just below the Transport 2 sensor located in the side...
We have been replacing the fuser too. I don't think there is going to be anything we can do but thought I'd post.
Rates are the shits on all these accounts we have these machines in and locked in...
It's the fuser. Tech sent me the unit. I put it in a brand new machine and ran 400 pages in SP modes. Made the noise. Put the new fuser in. No noise.
I can't make the fuser output check work on...
Howdy folks,
I got a few IM C4500 or 6000 singing the song of it's people. Its coming from the fuser. First machine was brand new, it was not very loud but you could just hear it. The other 3...
You should start your own post vs opening using one from 2011.
Please hire a tech as i don't think you have a clue of what you are doing and will likely do more harm than good.
H4 is a fuser...
Howdy folks,
Not sure about all of you but i have a hate for these internal finishers. Ive never seen the timing issue from the disposition tray but ive had lots of them that roll the paper...
Checked back with the customer. They found something. I asked exactly what the fix was and he said the AP was set as a public network and not a private. Not sure why it could still ping. Anyways...
Thanks for all the replies, unfortunately nothing has resolved this. One of our install guys asked if the 2g and 5g is being mixed on the same SSID. He's run into alot of issues on SHAW routers...