Search:

Type: Posts; User: mdm

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: Riso EZ 220 customer don't remember password to use device

    Thanks 20guage, I will give that try.

    I really appreciate it.
  2. Riso EZ 220 customer don't remember password to use device

    Good day, want to know how to remove the user code on a Riso ez 220, I have been searching the manual and cannot find it.
    can some one help with this. Thanks
  3. how to replace transfer belt assembly and reset counter

    Good day, I have a customer that has a torn transfer belt assembly, and I am about to replace the assembly, but I don't have a manual.
    I thought the wc 6515 were similar to the wc 6505 but they are...
  4. Replies
    1
    Views
    2,013

    Brother MFC 7820 scanner lock

    Good day, I am getting this message Brother MFC 7820 scanner lock and can not use the device. Any advice, I power off for a few hours and power on, but still getting the same error.
    Thanks
  5. Replies
    5
    Views
    2,056

    Re: Fault 191-310 WC 6027

    Thanks Howling, how do you return the values? When I power on machine it goes into fault and I can not do anything.
  6. Replies
    5
    Views
    2,056

    Fault 191-310 WC 6027

    Good morning good techs,
    I am having a problem with a Xerox work center 6027. The device was functioning when I went to the call. The customer called about a copy quality issue, light yellow...
  7. Re: Riso RZ390 Making Blank prints no image on master

    Good day thanks for your assistance,

    I did check for two master sticking to drum and original scanning blank side and everything was correct.

    I also replace and adjust Thermo Print Head to new...
  8. Riso RZ390 Making Blank prints no image on master

    Good day I'm seeking some help or advice on a Riso RZ390.
    Riso RZ390 Making Blank prints no image on master.

    Any help would be appreciated.

    Thanks.
  9. Xerox B8045 not copying 2 to 2, no fault codes. It would print configuration report.

    Good Morning,

    I need some assistance I have been working on a xerox B8045 that does not print 2 to 2. it gives no error, it just does not print 2 to 2. The other duplex features work fine,...
  10. Replies
    1
    Views
    140

    Ros system fault wc5875i blank copy/ print

    Good day, l have been working on this problem for a few days. The problem is ros system fault and continuous copy/ print blank. I have replaced single board controller, ros. IOT, PvP and alboot...
  11. RISO 390 display 4 ( master section) and check setting light not doing anything.

    Good morning,

    I have been working on a Riso 390 that is displaying 4 ( the master section) and check setting light. I check the master section there is no jam, replace master. I check the manual...
  12. Re: Xerox workcentre pro Jamming only on tray 2 with 072-105 code and grinding noise.

    Thanks for the help.

    Got problem solved, it was the feed head replace and problem solved.

    Mdm
  13. Xerox workcentre pro Jamming only on tray 2 with 072-105 code and grinding noise.

    Good day,

    I wanted to know if anyone has seen the problem of a xerox workcentre pro jamming only on tray 2 with a code 072-105 and a grinding noise.

    Thanks for help.

    Mdm
  14. Re: xerox 510/8850 engineering black band about 11 inches apart

    Hi Phil,
    Check fuser lamps, they are good with no rings. But I also put in a brand new fuser and still getting the same issue.

    It appears that fuser is fine, I am wondering about voltage and...
  15. Re: xerox 510/8850 engineering black band about 11 inches apart

    Thanks Phil, But I check hot roller and lamps and could not find nothing physically wrong.

    mdm
  16. Re: xerox 510/8850 engineering black band about 11 inches apart

    Thanks Phil, but the image is fine it is the black line that can be rubbed off with a little force. When I saw this I checked that the fusing web by removing it but it still copy and print with the...
  17. xerox 510/8850 engineering black band about 11 inches apart

    Good day having a problem with an engineering printer, that is printing and copying with a black band that
    can be rubbed off and is about 11 inches apart. When I cleaned the printer the black band...
  18. xerox 510 creasing paper when paper low 36 inch roll

    Good day,

    I am working on a xerox 510 that has two problems

    one it is creasing when paper roll get low on paper. When the roll is replace with a new roll creasing stops until the roll gets...
  19. Xerox wc 7835 that reading 30 percent on a new toner

    Good day, I am working on a wc 7835 that started out asking for toner now after updating firmware and performing nvm intialize it is now reading 30 percent on a new toner. has any one came accross...
  20. Replies
    0
    Views
    1,750

    wc 3045 with fault 61-370 code: 4000000

    Good Morning, want to if any has come across this fault with xerox 3045 61-370 code: 4000000 and says restart replace printer. This happen after an attemtp tp upgrade firmware. Any help.
  21. Thread: Error d-04 534

    by mdm
    Replies
    8
    Views
    6,496

    [Error Code] Re: Error d-04 534

    Hi right I am using black, no color.
    I have tried a new drum and a new toner, but I am still getting the same error.
    Could it be a board.

    mdm
  22. Thread: Error d-04 534

    by mdm
    Replies
    8
    Views
    6,496

    [Error Code] Re: Error d-04 534

    Thanks Liatang,
    that is the ink I am using, Can it be that I have to reinstall drum? If so why?

    mdm
  23. Thread: Error d-04 534

    by mdm
    Replies
    8
    Views
    6,496

    [Error Code] Error d-04 534

    Good day, I wanted to get some help with a problem I am having with a
    with a Riso 390 UI. It is showing an error d-04 534, I look up the error code d-04 534 and found that the ink is wrong. I...
  24. intermitting jams 0n xerox wc 5222 with 77-106 faults

    Hi guys, looking for some help got a xerox wc 5222. that is jamming with 77-106.
    I tried replacing fuser senser, fuser. I check and lubricate drum shaft and spring.


    mdm
  25. Re: Riso ez 390 jamming after replacing broken spring

    Thanks guys for your, I got the problem solved. The absorber was worn.
Results 1 to 25 of 132
Page 1 of 6 1 2 3 4