Search:

Type: Posts; User: Craigdumass

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    2,956

    Go to device settings and change your emulation...

    Go to device settings and change your emulation under PDL to PCL5 and see if this takes care of it. I would check your firmware on your print sytem and IB21E to make sure they are up to date. Last...
  2. Replies
    4
    Views
    930

    I have 25 of them out in the field with no...

    I have 25 of them out in the field with no problems so far, have you been installing the cassette heater plug and been keeping the firmware up to date? The Reason I ask this is there was supposed to...
  3. Replies
    5
    Views
    796

    You can adjust the simulation for the sensitivity...

    You can adjust the simulation for the sensitivity but the best fix is to buy some of those little felts that go on the bottom of chairs so you do not scratch a wood floor. Put one of them on the...
  4. I have had this even with the Kyoceras in a high...

    I have had this even with the Kyoceras in a high humidity low volume accounts. I just go in and bang the heck out of the cartridge or just simply replace. If you are using Generic good luck, it is a...
  5. Replies
    9
    Views
    1,447

    Yes I have had the main charge create a shadow...

    Yes I have had the main charge create a shadow and you can increase the cleaning cycle I just replace the two wires, I have had more problems as BlackCat described and have been doing the same...
  6. Replies
    10
    Views
    5,525

    There is a problem with the way the wire harness...

    There is a problem with the way the wire harness is wired you should call your technical representive because I am not sure if you have to order a new harness or just have to reroute the existing one.
  7. Replies
    8
    Views
    2,702

    1105 means that it is not even close to...

    1105 means that it is not even close to communicating, did you go back through your smtp settings and test. Maybe your authentication changed or your email SMPT Server name is not right.
  8. Replies
    4
    Views
    1,221

    Did you try changing the scanner timing,...

    Did you try changing the scanner timing, somewhere around sim 63 or 68?
  9. Replies
    8
    Views
    2,702

    You should be able to reformat the HD, you can...

    You should be able to reformat the HD, you can save your scan to PC email and address book to your thumb drive by using Simulation 917 to export this information when done you can import back in...
  10. Thread: KM 2530

    by Craigdumass
    Replies
    5
    Views
    1,218

    I have seen when you open the left side cover and...

    I have seen when you open the left side cover and you check out the 4 white rollers, there is a new updated assembly for that whole section that should be in the Falcon 2 bulletins. That part will...
  11. Replies
    6
    Views
    5,327

    Manual

    Yes go to the Kyocera Website log in and go to the technical resources tab then choose manuals, punch in black and white copiers. Then choose the 2050 manual and download it.
  12. Replies
    4
    Views
    1,084

    Thats right same issue as the Voyager series just...

    Thats right same issue as the Voyager series just a tiny bit easier to get at.
  13. Replies
    4
    Views
    5,046

    Nice reply, I have replaced three lasers in the...

    Nice reply, I have replaced three lasers in the past 6 months on these, I usually check the CW unit first before I replace the laser. When the Corona unit start arching to the drum in many cases it...
  14. Replies
    6
    Views
    1,711

    Very nice

    Very nice
  15. Replies
    14
    Views
    2,636

    First of all, what kind of volume is the customer...

    First of all, what kind of volume is the customer running along with what percentage of fill are they doing. If it does indeed go into Image cycle, I have had two of the following post from above and...
  16. Replies
    21
    Views
    10,756

    I carry a main charge for a 3035 and a 4050 in my...

    I carry a main charge for a 3035 and a 4050 in my car stock. 2bl93092 and a 302GRsomething.
  17. First of all did you try the 906 reset on the...

    First of all did you try the 906 reset on the machine, next since you have done the liftmoters have you tried replacing the recepticles on the back of the machine where the cassette plugs into and...
  18. Replies
    21
    Views
    10,756

    I kind of thought that was what I just said,...

    I kind of thought that was what I just said, except the toner build up comes from not cleaning out your two dust filters by the bypass, the problem is that heat builds up in the machine and causes...
  19. Replies
    6
    Views
    1,341

    Did you call technical support on this?

    Did you call technical support on this?
  20. Replies
    21
    Views
    10,756

    Replace the main charge unit, clean the two...

    Replace the main charge unit, clean the two filters by the bypass, blow out your seperation grid, and you will be good to go for another 100k as long as you have no tiny little pit holes in the drum...
  21. If the copies are just a little light rather than...

    If the copies are just a little light rather than changing out a drum right away I adjust background in the copy defaults.
  22. Replies
    16
    Views
    2,226

    I have downloaded the 2.40 and it works with the...

    I have downloaded the 2.40 and it works with the new scan to file utility.
  23. Replies
    5
    Views
    2,035

    Have you ran simulation 130?

    Have you ran simulation 130?
  24. I think its your dimm

    I think its your dimm
  25. Thread: Code c2600

    by Craigdumass
    Replies
    6
    Views
    3,476

    The machine must have some kind of jamming...

    The machine must have some kind of jamming problem when the customer removes the jam then they are not closing the left cover correctly. I would check your jam codes to find out why that cover is...
Results 1 to 25 of 61
Page 1 of 3 1 2 3