Search:

Type: Posts; User: printprocc

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    1,391

    Re: C7000P "Now Adjusting"

    Thank you to you both!!! I will reply back with what I find.
    Paul
  2. Replies
    8
    Views
    1,391

    Re: C7000P "Now Adjusting"

    Long story SHORT..... These folks have switched back to Xerox equipment and only have this one KM device left over. They had a KM tech who has been servicing this machine but they had to stop using...
  3. Replies
    8
    Views
    1,391

    Re: C7000P "Now Adjusting"

    Thank you for the quick reply!! Please forgive me as I am new to KM machines.. I service Xerox machines and am doing a customer a favor.

    No codes were given until I turned THAT DIP setting "OFF"...
  4. Replies
    8
    Views
    1,391

    C7000P "Now Adjusting"

    Hello,
    This machine starts fine but will not complete the "Warm Up" stage! Starts with "Warming up" then says "Now Adjusting, Please wait a while" but never completes the process. Stays like this...
  5. Replies
    35
    Views
    21,502

    Re: BizHub C554 paper jam at fuser exit

    Hello everyone. Just wanted to chime in and thank you ALL for the valuable input given. My issue was indeed cl8 and it has been replaced and the machine is up and running!
    As always you've all...
  6. Replies
    35
    Views
    21,502

    Re: BizHub C554 paper jam at fuser exit

    Ok so this HAS to be the problem...I did find a lot of what looks like iron oxide debris so this is at least a good start. Also looks like somebody but grease all over this at some point..SMH.... I...
  7. Replies
    35
    Views
    21,502

    Re: BizHub C554 paper jam at fuser exit

    Thank you 3ktlc! I went thru that entire section and made sure everything was moving easily and properly...I am further investigating cl8! I have a feeling that is where my troubles are but have...
  8. Replies
    35
    Views
    21,502

    Re: BizHub C554 paper jam at fuser exit

    Thx for the input! Attached is a list of the jam codes found right around the start of my problem.
    32-05 exit section
    75-42 fs535
    30-03
    9/17 is when the issue...
  9. Replies
    35
    Views
    21,502

    Re: BizHub C554 paper jam at fuser exit

    Figured I would try to attach pictures...if this...
  10. Replies
    35
    Views
    21,502

    Re: BizHub C554 paper jam at fuser exit

    Hi everyone,
    Sorry it took so long to reply, it's been a busy week so far. Thank you for the input regarding my problem alas I have not found anything wrong yet. As was suggested by EarthKmTech I...
  11. Replies
    35
    Views
    21,502

    BizHub C554 paper jam at fuser exit

    Recently replaced the fuser unit due to degraded heat roller. Dropped in new fuser and the machine ran fine for roughly 100 clicks (letter size) then jammed at the fuser exit. Several attempts using...
  12. Replies
    6
    Views
    4,025

    Re: Xerox 4595 Error code 010-315---HELP

    378043780537806Finally.
    Sorry for the delay, it's been busy. SO From what I see all the magnets and associated latchets appear to be straight and contact properly.
  13. Replies
    6
    Views
    4,025

    Re: Xerox 4595 Error code 010-315---HELP

    Hmmm having difficulty uploading pics
  14. Replies
    6
    Views
    4,025

    Re: Xerox 4595 Error code 010-315---HELP

    Yes they all appear to be.. Everything seats nicely and the magnets are firmly planted in what looks like the proper position.. I will try to post pics from my phone..brb
  15. Replies
    6
    Views
    4,025

    Re: Xerox 4595 Error code 010-315---HELP

    Thx for the reply.. Yes this is where I started.. Did all this and no change.. I can go back over it all a third time and maybe look closer but I doubt the result will change
  16. Replies
    6
    Views
    4,025

    Xerox 4595 Error code 010-315---HELP

    Hey everyone, hopefully someone can shed some further insight as to what to check. Xerox support site only tells me to check the fuser draw, duplexer tray and cycle power.. DOne all that simple stuff...
  17. Replies
    6
    Views
    1,396

    [Dead] Thank you for that reply..ill have a look in the...

    Thank you for that reply..ill have a look in the morning but have a feeling its not paper or dust.. with my luck.
  18. Replies
    6
    Views
    1,396

    [Dead] Re: Docucolor 240 does not completely boot

    HI all, finally got the machine to actually boot.. What a process but figured out the timing I had to hold and then release those buttons was critical.. No matter..it is on..HOWEVER I am back to...
  19. Replies
    6
    Views
    1,396

    [Dead] Re: Docucolor 240 does not completely boot

    Hello again,
    So another update. My hard drive is actually fried. Any way to get an image of the software on this machine that I can load on a replacement drive??
  20. Replies
    6
    Views
    1,396

    [Dead] Re: Docucolor 240 does not completely boot

    Ok I am updating my original post above. I put the hard drive into another pc and it was recognized as a hard drive and past hard drive diagnostics.
  21. Replies
    6
    Views
    1,396

    [Dead] Docucolor 240 does not completely boot

    Hi Folks,
    I'm hoping you can give me some assistance with my issue. Dc240 was running perfectly on Friday until it randomly stopped after running all day. Error message on the screen was 010-322...
  22. Replies
    9
    Views
    3,068

    Re: DC 240 CK ROS replacement

    Good morning again folks,
    Thought I would give an update regarding my continued struggle trying to calibrate this machine and unfortunately I am still a bit stuck. Ever since changing out the CK Ros...
  23. Replies
    9
    Views
    3,068

    Re: DC 240 CK ROS replacement

    Thank you. That was very informative. I will check that software level when I get back in front of that machine.

    Happy New Year.
  24. Replies
    9
    Views
    3,068

    Re: DC 240 CK ROS replacement

    Thank you Exok,
    I too did not find anything in the EDOC regarding any other adjustments but the ones you mentioned. I went in and out so many times trying to get the original ROS to work, I probably...
  25. Replies
    9
    Views
    3,068

    DC 240 CK ROS replacement

    Good morning folks,
    I recently had to chase down the faded cyan stripe on my print outs and as expected found a bit of toner spray on the CK ROS glass window. I figured it would be a good time to...
Results 1 to 25 of 35
Page 1 of 2 1 2