Hello all
Today we have a fuser motor failure 10 330 but the motor runs fine
all the rollers, gears and bearings are fine
since we have two of these machines I swapped the fusers and the fault...
Type: Posts; User: otomatic
Hello all
Today we have a fuser motor failure 10 330 but the motor runs fine
all the rollers, gears and bearings are fine
since we have two of these machines I swapped the fusers and the fault...
more Fiery V80 antics
we've had years of communication issues with ours
and have managed to solve most of them
one of which was memory errors when updating the patches
cleaning the hard drive...
got the 90-01 on one of our machines and swapped out the adu board and the code cleared but now the fuser will not light up and stuck on copier warming up
if I put the old board back in and start...
Hello All
we have one of our 920's punch unit constantly jamming which is being caused by the motor that drives the punches occasionally overrunning it's home position
for example when running...
we have just got the sc 81-01 on our machine
it was jamming then kicked one the fuser temp codes and I reset that then I got 81-01
is that code a firmware issue and if so where on earth do I find...
same thing happened here after some electrical work was done to the building and only had 110 (one leg of the 220) at the outlet ...just the green light and nothing else
Hello all
constant jam out of tray 3 running 11x17 two sided
I have cleaned every roller, clutch and sensors including swapping all the same and no luck
I removed the vertical conveyance door...
it ended up being the ribbon cable to the CCD
we have the same code going on here today and at a total loss
it kills the machine dead even in 36 mode
we have some spare parts machines and I have switched out all the parts indicated in the...
sorry for not getting back to this sooner but here is what I have now
the banding was just an old and bumpy lower transfer roller
I was able to work around the transfer issues with lowering the...
yes it was...and thanks mr spock...I just didn't quite understand exactly what nic was till a former rep came by the shop the other day and said just plug it into that one, it's where the firmware...
problem solved
...I just had to plug the network cable into the other jack on the machine and presto web utilities
now going to attempt loading the firmware
well after looking at operator manuals I was able to turn off the page scope thing and now I get a 501 not implemented error
just trying to install new firmware with the ISW internet according to the instructions in the service manual
but my web browser only shows page scope and not the web utilities which wont let me in...
thanks for the troubleshooting guide
I did get better results setting all the trays to recycled paper but still getting a lot of banding on side two
the bands are generally darker and sometimes...
I've recalled all the standard data
I've searched the manual and don't see any transfer assist to set
I did a test print 9 and side one is ok but has some dark banding but not bad
side two has...
we are having the same problem with our 920 at two mil
all kitted, new dev and drum but nothing has changed
test print 12 8'5 by 11 bond two sided
solid squares look great but the midtone screens...
I've checked the lamps and they are ok
checked wiring from the AC board to the lamps and ok
but the ground was open...traced it to the thermal protector and it was open
new one on the way...
is the SSR the relay on that board? if so iv'e checked those out and they seem to be working
they both (AC board, DC board) click on then off at start up then the code after that
I didn't check...
hello all
our ir105 has started the day throwing codes
the first one was 010 and did the troubleshooting in the manual only to have it now do a e000 then cleared it and now it's doing e004-0001
...
hello all
we've just got our first canon machine
it's an ir105 with a k3 finisher and so far it's doing well
but is there any way to set the counter to display the count of completed booklets...
no problems with the IP602 that I'm aware of
this machine simply won't center no matter what 12-3 is set to
I've done these adjustments on our other 85 and it works perfectly
I do have a parts...
Hello all
we have a 7085 that the image will not center
the printer centering adjustment in 36 mode does nothing
test print 16 is to the left of center 3mm
we adjusted the trays to get it that...
hey thanks guys for all the info
I'm going to play with the temps next as some stocks seem to fuse better than others...it is curently at default
all the mechanical bits seem to be in good...
hello all
we have a 7085 with a fusing problem (image rubs off)
and have tried everything we can think of
it was giving various codes for fuser temps and replacing the rollers seemed to do the...