clean the rollers with sandpaper and no more jams i also do this on other AR machines and MXM machines
Type: Posts; User: georgereth
clean the rollers with sandpaper and no more jams i also do this on other AR machines and MXM machines
hi .
does anyone knows where to find USB drivers for AR-M207 WIN 10 64bit?
thanks
Replaced clutches in feed trays and flushed registration clutch
i have not replace registration mylars the are fine , and finaly no leaking of the dev. unit
it is read first
in the first time with the network scan tool i see the machine and i try to give the new ip adress , and in the writing progress to the copier the power is cut off . After that it...
in this machine when i copy from the bypass tray works fine . When i try to copy from the tantem tray or the other two trays then jams the paper in the registration sensor , begore the registration...
First time after installing the machine I try to connect it with the computer I use the CDROM and first thing to make is to give the IP adress to the nic card of the machine , during the progress (...
after many hours of searching i gind out that the toner chip (on 2 original cartridges ) is damage .
I please i 3 toner and the machine start working
thanks for the help
I have install new toner and the machine does not go to ready and the toner is blinking
I notice tha the machine starts normaly (scanner-exposure lamp-op.panel) but the main motor does not run and...
eyxaristo poly file moy .
an xreiasteis otidipote steile moy mynhma .
doyleyo se kyoceramita-ricoh-sharp-oki-konicaminolta kai merika canon
how can i reset the error PLEASE CALL SERVICE 003 or what i have to replace?
thanks
Thanks
Can you please tell me the parts number of the fusing unit 220v Ir2230 ?
thanks
I have done this and i have the same problem
yes is the same machine
i have notice that i cant see if the nic is eneble or not
i have found on the service manual about that and i want to check if its correct
i have the same problem and i...
how i can get to the ssp mode or the GW SP Mode Tables
actualy i want to get access in the 5985 001 On Board NIC to enable it
thanks
No red light appears on the printer button and finaly
i have use "DDST Printer Driver" instead of DDST for PCL on port 10001 with the same problem it does not print
the paper size settings are ok
yes i have changed the port from RAW to LPR and put "print" in the LPR queue
the same problem it does not print
have mp 2000l connectet to the network with ip , subnet , getway adress ok
i scan to the computer and if i but the ip adress on the explorer i see the machine
i cannot print from the windows 7 . i...
i have mp 2000l connectet to the network with ip , subnet , getway adress ok
i scan to the computer and if i but the ip adress on the explorer i see the machine
i cannot print from the windows 7 ....
yes i run the f8
when the machine is at warming up the c2557 is displayed
i have change the drum unit and the developer unit and the developer
any ideas about this problem ?
or i have to Replace the PWB-A board
I have a problem with this machine
first when i turn on the machine its start runing (drum-developer motor) and shows please wait . It does not stop , when i open and close the font door or the main...
THE COPY QUALITY IS LIGHTER 10mm IN THE BEGINING OF THE PAGE . I HAVE CLEAN THE OPTICS
NOTE I CANOT PERFORM PRINTER CALLIBRATION COPIER CALLIBRATION IS DONE
ANY IDEAS?
THNKS
take out each feed unit replace all the one way gears , clean the entire unit (bushings,shafts,quides etc) and finaly check also the belt and the gear in the drive motor of each feed unit
I forgot to say that i have done firmaware upgrade and the machine does not have fax kit