RESOLVED. Contact on rear of drum cracked behind gearbox. Causing no contact to charge roller. Hard to see at first. Replaced contact and all ok. Thank you all for your help and support.
Type: Posts; User: spaceman99
RESOLVED. Contact on rear of drum cracked behind gearbox. Causing no contact to charge roller. Hard to see at first. Replaced contact and all ok. Thank you all for your help and support.
Hello
Can you help please ?
Have a Ricoh mp2001 . Doing solid black copies. Changed HVT Power pack and PCU . All connection on rear of PCU look good. Was thing BICU ? Any ideas welcome. Thank...
hi.
all that is need is a 65mm (2 9/16 ) bearing puller and triflo oil. Takes about 30mins to get machine back up and running. If PCU is not damged.
Stage 1 : open the PCU as far as you can try...
hi
hope someone may of seenn this before. it an old Ricoh MPC 2051ad.
Test prints from SP mode = all ok
print = ok from Driver
37829
Fault: see image attached
When copy off ADF (...
Hello
Have got a MPC4503.
1st call.... Dead mch reported and smell
2nd call.. eng fitted PSU, however, no SP mode or other functions. then fitted Controller.. Got copy screen and function...
Hello
I have a pro c 5110s with NO FIREY. It has a LCT and booklet finisher
When in copy mode you can print many pages from the LCT using the paper library .
When using the USB ( ops...
Hi - sc322 - Development bias: high voltage error: M
replace the toner hopper and poss re dev magenta
Hello
Machine : Pro C 901 has buffer ( cooling unit) and sr500 finisher on it.
Fault: 901 main frame ( engine) working fine......however does not see sr5000 finisher . Does see the buffer....
I have this problem at the moment. Did the mylars resolve this issuse. ???
My error is . The adf feeds in the paper and the ejects it ( simplex and Duplex ) but does not appear to see the trail...
Hello
CAN YOU HELP ????
Have a mpc5002 with please wait and no fuser temperature increase and NO fuser error.
Removed HDD and formatted it and re installed, only to get SC564
Replaced...
Hi World....
I have a Katana (pro 1107ex )
Message replace recycle unit soon.
1st visit = SC478. Torque limit reached 10 on recycle unit. Found Coil in Cleaning - transfer assy broken....
Dusting in this machine.
I agree dev related.... Normally someone has forgotten to put the dev filter back in the dev unit. Also change the air flow filters, all 3 of them .
If the dev seals...
Hello
Sc670 = controller baord.
had this many times and it worked.... also check the pins inside the Rj45 conector as these sometimes bend and short the board out.
good luck .........
Hello all off above.
I went back today as PR for the user and the machine is still working.
It would appear after checking every thing. It was caused more likely by the tray inner metal...
Thank you all very much for your input... really weird fault. Coupler was fine and the Sp 's did not effect it. I changed all of tray 1 mag with tray 2 yesterday. Hence why i put the fault out to...
Hello all
I have a MP3350 that will not feed the paper from tray 1. As the tray does not appear to lift high enough. Works with 20 odd sheets but any more wait in it , it fails.
so far.........
take the HHD out and put it on a cradle attached to a pc. Format HDD and 9 out of 10 time it recovers. After reinstalling it in the mch format it again in Sp mode
Also check the fuser on the...
thermal pile broken that sits above the fuser. Bit of a tricky job and a major strip down. Wise to always try the thermistors 1st , check contd: of the rollers.
if you can swap the complete...
yea agree . Transfer roller bushing failed. . i bet if you push the door the noise stops......
good luck
681 = HDD error and Firmware. had this before on this machine and replaced the HDD and all was ok.
good luck
sc552 : thurmisotor, p roller and Bearings cause this along with . Rearly : the bracket on IH inverter or Defective IH inverter damaged
Paper stuck ( mch stool ) at registration: Eprom in...
Hi
Have you tried it on single colour.....?
TTT: Adjust the enterance guide to the fuser plus increase the Lead edge in Sp modes. Also look out for crap on the strpper bar.
Good Luck
Add Toner = Print off a Non default smc if you can. Drop the NVRAM full reset. Load in the non default settins and set up the registration. VERY INPORTANT to do the reg.
This will sort it.
...
Power on jams = two sensor in the brige unit need replacing as well as updating the firmware.
Try tappimg the bridge unit and you should see the alarm light come on/off
Re exit jams = clean...
If your getting intermit'' Sc 542 try changing the 2 sensor at the front for the machine for the coil drive. If it still does it, change the little fuser drive gear in the fuser drive assm, bit of...