The only time I've seen this is when one of the black plastic holders on the right side of the TBU assy is broken. This will cause the belt to walk towards one side. There are two of these, both on...
Type: Posts; User: audioimaging
The only time I've seen this is when one of the black plastic holders on the right side of the TBU assy is broken. This will cause the belt to walk towards one side. There are two of these, both on...
Two things to look for. First, check your developer unit to see if your augers are turning. I've had developer units lock up in the past and this would be one symptom. Also the gears driving the...
Anyone in the Washington DC area have use for a 2238c with finisher. Has most options but no post script printing. Low copy counts and runs well. Make me an offer. It's in my basement and the wife's...
Has the pcl print, scan and fax option as well as the large finisher. Fairly low counts on consumables and total counter and good working condition. In D.C. area.
Any reasonable offer accepted.
...
It's already been mentioned but to be more specific, Check the blue connector on the rear of the fuser. A couple of the pins on there are known to fail causing this problem. Sometimes you can repair...
Toshiba would tell you to replace page memory ram on sys board and that may help, but the only time I've experienced this, it went away after IMG board replacement.
Bought this for a machine that was going to be refurbed but wound up with too many problems and was subsequently junked.
Now, I have no need for this dev kit and would at least like to get some...
There was a SNL spoof commercial a few years back with the same premise. I believe they called it the Assmaster. It had a contoured glass for more comfort.
When you pull the developer unit out, is there toner surrounding the hole where toner enters developer unit?
I have seen cases where the seal on the toner exit assy fails and allows toner to...
When you replaced the glass, did you only replace the big glass or did you also replace the small slit glass to the left?
The adf only uses the small slit glass and any spots on that show as...
Before taking anything apart, try calibrating for copying. Go to user functions and look under the general tab in Admin or user (it can be in either) for calibration. Choose copy and calibrate. This...
If you replaced the cam already, then you need to look at the rest of the assembly the cam drives. I've seen this caused by the pin missing on the shaft behind the cam (it can fall out if one is not...
I've picked up some machines that had Katun drums in them which seemed to work OK. Feed rollers shouldn't be a big deal. It's toner that is the biggest issue.
That said, the OEM fuser rollers can...
My wife makes more working at Costco.
Good luck with this...
They are pretty good machines with OEM toner. I don't mess with generic toner so can't tell you any that would work.
Beware of C970 codes which are common. Caused by charge corona arcing. Toshiba...
There is no current driver for Snow Leopard. Last I heard was late January.
There is a workaround by altering the current driver using CUPS, but I have not attempted this.
If you have a CEB0 code, disregard what I wrote previously.
This is a common problem. Toshiba initially tried a mod kit which added some pieces to the front of the cam shaft. This doesn't help. ...
This code is not in the manual. Did someone try to copy money???
Your ccd unit is starting to fail (common to this machine). replace the ccd/lens assy.
Ask in the Ricoh board for the 5560c and you'll probably get an answer quicker.
It's in the User tools but I don't have one in front of me to go through the screens.
Can you download operator...
Get the code and prepare for some fun.
You probably have a drive belt failure. There are multiple belts in the drive assy and when the right one fails, you get this symptom.
Toshiba has a...
Go to Top Access (from a computer on the same network as printer, launch internet explorer and enter the machines IP address in the URL). Log on as administrator (user name is admin, default password...
Don't know about prices (I never see prices on contract machines). You might have more responses on the Ricoh board (ask about 5560C).
At 200k, you shouldn't need any fuser, transfer belt or feed...
It is a Ricoh (aficio 5560c derivative) and they work pretty well. Really good as a fast color copier for paper up to 28lb.
Not as good with thicker paper as some machines.
Could be good at...
They are all the same box. Just different speeds.