Good day all. I have a customer that wants the ID Card function available when scanning to folder or email. Unfortunately it does not look possible. The combine function is what produces id card...
Type: Posts; User: brancas
Good day all. I have a customer that wants the ID Card function available when scanning to folder or email. Unfortunately it does not look possible. The combine function is what produces id card...
yes in the margin area and the bottom half of the page
All colors. Cyan toner is finished. Original toners
Hello everyone. As the post says have a 356ci that is ghosting on prints and copies. A MK A kit was changed and the tech assures me that the machine was switched off and unplugged before the kit was...
Had that same issue on A FSC 8520. After changing the black dv ,DR 895C drive unit(which also drives the black dv unit) with no change I installed a Engine board and it worked.
Good day all. Customer's TA 356ci is making a grating noise. When i run Maintenance Mode U30 the noise is emanating from the feed drive unit. Feed drive drive unit and toner supply assy were replaced...
That was great advice. Retraced my steps and-installed the original interlock front switch, Working again. Thanks a lot!!!
Hello everyone. TA 307ci had a gear grinding noise. Followed tech bulletin 2R4-0030 to replace toner supply unit. On reassembling machine had a front cover open message. After troubleshooting...
Just an update. Gave the tech a used laser unit from a working machine and that solved the problem. Thanks for all the helpful advice!!
The transfer belt was used taken from a working machine. Dv refesh did not work. Toner is OEM. The tech did remove the laser unit and cleaned all mirrors. Will give him another laser unit to install.
Transfer belt was replaced
54127
hey guys. I have a TA 3051ci giving light prints as seen on the attached doc. The tech assigned to the customer serviced machine ran drum and developer refresh laser scan cleaning...
tried the harness and feed pwb 1. turned out to be the engine board. thanks for the advice.
[QUOTE=blackcat4866;1942130]The manual points to a communication issue between the motor control PWB and the engine PWB.
If you're not ready to go for the engine board yet, you could try the...
Having a c2950 on a TA3051ci error pointing to the motor control pwb. Also the machine is indicating paper jam and main cover open symptoms similar to a C980 error which is the low voltage PWb....
Good day all. FS 6525 DP paper feed motor is constantly on. Upgraded firmware cleaned all sensors on DP. Replaced said motor and DP Main PWB. Problem still persists. Have two clients with exact...
Hey guys. Have not been to this customer myself. TA 3252ci displaying system error 900044797. Checked service manual no info for this. Did not get much info from assigned technician only that it...
Feed PWB was changed along with firmware.
Good day all. Customer's TA 5052CI can print from cassette 1 and 2 intermittently but paper z folds and jams in fuser unit and errors out. From cassette 3 and 4 jams in fuser unit and also errors...
Had a similar issue with a TA 6501i. When attempting to copy or print from cassettes 3 and 4 machine would be stuck at processing. Turns out paper was stuck behind the B1 tray for cassette 3 and 4...
TA 7002i with C3200 error. Followed all steps in service manual (Installed latest firmware checked and replaced led lamp, fcc cable,ccd pwb lens unit engine board) problem still exists. Replaced said...
Update. It was the control panel that was the issue. Installed a working control panel with the new main PWB and I was able to enter the Maintenance Mode. I even tried the original Main PWB and it...
these models do not have an eprom on the main pwb. Only on the engine board. my issue is that I cannot enter into maintenance mode to perform U004
I did open front cover and right door no joy. will check pwb and let u know
Check if the drum unit is turning as it should. It may where the drum is connecting to.