I know thats why i said 99% of the time had techs go in and adjust everything they can touch and made the problem worse just try the basics first and like i said most of the time the fault goes away...
Type: Posts; User: welshman
I know thats why i said 99% of the time had techs go in and adjust everything they can touch and made the problem worse just try the basics first and like i said most of the time the fault goes away...
This is a old problem on these machines what you need to do is the following to clear it
go into service mode and do dc con clear
open the front door
turn off the machine
turn on the...
you can do this without running the copier into the wireless router
buy a dlink wirless bridge and connect this to the copier then you can have the copier whereever you want no need to be near a...
it can be the pick up unit for this machine is all in once both tray are together and they do have drive gears that snap
only way to fix is replace the unit
or check for other issues ie reg...
Its Easy
Right hand side of machine pull out tray
above this is a cover one screw remove screw and cover
open front door rack down the handle
right hand side slide out the transfer belt...
If this machine is throwing a error saying the waste toner sensor faulty it is not
it is sensor pi11 the one on the cleaning assembly shutter it gets coated in toner and shows this error
...
You need to make sure the machine has a network boot rom in it as well
*2+8* then copier then display then version scrool for boot and make sure it is not a C rom if it is will never print
you should not be near a copier if cant replace the drum unit
but
open toner hopper door remove 1 screw
left side remove screw near the front of copier
remove front panel
i took out the power supply noted the model number then googled it
found one from a psu supplier at a third of the cost canon want not they will sell you a psu anyway
save me a fortune
post the spreadsheet in here i will gladly use it lol
save me a lot of head scratching that will
happy new year
if you have ecopy you dont need to use scangear just use the ecopy instead
also those machine have a send kit so again i would use this and not scangear
scangear is slow on colour machines...
codes are
2000
3000
4000
5000
or Admin
or Admin01
canon have brought out a new paper sensor for the vertical path as the old ones get worn out
the old ones are just black and can look ok but there worn
the new ones have a metal cover over...
you need to reset the error code as well
enter service mode 4 to release the error
or turn the machine off at the wall for a hour if you dont know how to get into service mode
comopn fault for this one is paper caught inside the conector top tip for checking it though
remove panel from exit end of machine pull out unit and then you can see the conectors without...
also when you do dc con clear leave the door open as it wont clear the reg settings if you dont
found this out for a canon trainer 6 mnths ago he did not think it mattered till he had a problem...
you will have to change that sensor one day
if you read the post he has changed the drum transfer etc etc
and now its time for the sensor have ahd over thirty machine do this once yoyu...
reload the system software for the rip this will work unless the hard disk us
laptop size drive and you can use any make not like the copiers
been using it for 6 months
better than vista and xp
its vista stipped down and works its all the best bits of xp but none of the vista rubbish
good o/s so far no problems
no you cant
copy qualityb will be rubbish the toner for the ir6800 is finer and the bias volatages different
you will then have to vac out the black dev tank not worth the effort
easyiest way is to go to copier and select change paper size to auto in the printer settings
change the drum potential sensor
when you tried all else it always is this sensor
its housed above the drum have to remove the td assembly to get to it though two screws and replace
...
check fan for transfer bed
check the belts are moving
check the fuser inlet guide not fallen off
check paper size set right on the cassette
another thing to check is the blank exposure lamps all working they provide blank lead edge
also check the blank lead edge setting if set to nothing the toner will foul up the charge roller...
yes its easy three things you can do
1 :- Rewire the corona unit including the grid (sometimes works)
2 :- Clean the corona unit fully side shields and frame to remove all ozone deposits...