Search:

Type: Posts; User: frodo

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: SMB scanning

    by frodo
    Replies
    13
    Views
    3,335

    Re: SMB scanning

    What Send Error Code are you getting?
  2. Replies
    4
    Views
    2,622

    Re: Kyocera pop3 5550ci

    Honestly I hate this method with pop printing, I can see the benefit but it will cause more trouble in the long run. If it gets a bunch of orders all at the same time it usually delays marking the...
  3. Replies
    14
    Views
    7,296

    [Misc] Re: Ecosys M2040dn Twain Scan driver

    Isn't there a WIA driver, Or doen't this work with Word?
  4. Thread: TA3232

    by frodo
    Replies
    8
    Views
    1,275

    Re: TA3232

    Yeah it can be done with prescribe but it's awkward to setup.

    Try using the KX print drivers Watermark feature, Takes a bit of playing around but it works fine, We have several clients using it.
  5. Replies
    24
    Views
    4,066

    [Misc] Re: Black print in copy mode FS-6025MFP

    If you have already changed the Power supply, you'd be pretty safe trying each one (NOT BOTH AT THE SAME TIME) and remember the dimm / eeprom, In the colour machines it was usually the Main pcb from...
  6. Replies
    24
    Views
    4,066

    [Misc] Re: Black print in copy mode FS-6025MFP

    Yes, It was common when the PSU went bad(Pregnant Caps) or blew, it takes out the eng/main board, and then you get black scans/copies.
  7. Replies
    9
    Views
    4,039

    Re: Mac job accounting/ pin print documentation

    Agreed, you must use the Mac Phase 4 driver for JA to be available in the print panel.

    To set defaults you can access the old http://127.0.0.1:631/printers to set global defaults.
  8. [Jamming] Re: A3-2 sided jamming in the feeder with jam code 9500

    Yeah there's a small pad that the switchback solenoid hits as it is fired outward, the pad gets damaged and sticks to the solenoid pin.
    I usually remove the pad and replace with something a bit more...
  9. Re: Is it possible to use VNC to control TaskAlfa machines?

    I realize this is an old post.

    I know you can on the Iris series machines. Not too sure on any older ones.
  10. Replies
    15
    Views
    5,664

    Re: FS-C8525MFP, massive voids with K

    From memory these little beasts have a K dev drive clutch on the back of the main gearbox, 302K094320 - PARTS CLUTCH 50 Z45L SP

    We had lots of them go on the 8020 - 8025's

    Very easy to get to...
  11. Replies
    17
    Views
    2,580

    [CQ] Re: HP T2300 eMFP Print Quality Issues

    Turns out is was the Engine PCB causing the problem
  12. Replies
    17
    Views
    2,580

    [CQ] Re: HP T2300 eMFP Print Quality Issues

    Well i tried a new carriage unit now and it still hasn't fixed it, The firmware is up to date also.
  13. Replies
    17
    Views
    2,580

    [CQ] Re: HP T2300 eMFP Print Quality Issues

    I have been leaning in that direction, Carriage PCA or just bit the bullet and replace the whole carriage.

    Expiry, True but for warranty purposes it's just wiser. This model makes notes of all the...
  14. Replies
    17
    Views
    2,580

    [CQ] Re: HP T2300 eMFP Print Quality Issues

    Yes it is rotated,

    The left of all of the images is the leading edge of the print.

    The machine came to us with the fault, All heads and ink were out of date.
    All print heads and inks were...
  15. Replies
    17
    Views
    2,580

    [CQ] HP T2300 eMFP Print Quality Issues

    Hi Guys,

    I'm having a problem with a HP T2300 Plotter, Image quality is out of calibration on the Cyan/Magenta Head only.
    34192341933419434195
    As usual it looks like a normal print head issue...
  16. Replies
    15
    Views
    7,915

    Re: A battery powered 5 port switch

    Excellent, Just bought 3 of these for my techs.
    $10.63 and free postage and had Aus Stock aswell

    Thanks.
  17. Thread: TaskAlfa 300ci

    by frodo
    Replies
    10
    Views
    1,956

    Re: TaskAlfa 300ci

    There was a TI on this very similar issue quite a while ago, I'd be looking at the developer drive motors. It's a common issue on the saturn series where the motors fail without bringing up an error...
  18. Replies
    2
    Views
    3,251

    [Error Code] Re: Xerox Docuprint C4350

    All fixed thanks for all your help :P
  19. Replies
    2
    Views
    3,251

    [Error Code] Xerox Docuprint C4350

    Hi Guys,

    I've been working on this machine for a while now (c4350) without much luck, I have rectifies all the physical problems with the machine - The transfer belt was Torn and needed replacing....
  20. Replies
    0
    Views
    701

    Panasonic DP-8020 Parts for ADF

    Hey guys,

    I'm looking for some parts for a DA-AR202-PBR ADF

    Looking for the Feed Assembley - I have one that keeps falling down so that your originals hit the rollers when you feed them in...
  21. Replies
    4
    Views
    1,153

    Re: Need a fax sys n for cs2525e

    Anyone else got one for sale?

    Please PM me
  22. Re: Looking for fax system n for kyocera/copystar cs-c2525e

    Hi Guys,

    I'm also looking for a Fax System N, E or non E series will be fine.

    If anyone has one they can sell me?

    Thanks
  23. Replies
    0
    Views
    940

    Xerox DocuCentre II C3000 needed.

    Hi all,

    Any help would be great thanks.

    Cheers.
  24. Replies
    3
    Views
    1,337

    Thanks guys, much appreciated ;-) Frods

    Thanks guys, much appreciated ;-)

    Frods
  25. Replies
    3
    Views
    1,337

    Sharp AR-M316 (AR-RP7 Doc Feeder)

    Heya all,

    Just needing part numbers for the AR-RP7 Document Feeder Pickup Rollers (there are two of them, 1 pick-up and 1 paper feed) and the Seperation Pad.

    Thanks.
Results 1 to 25 of 37
Page 1 of 2 1 2