The lines in the attached foto seem to be out of focus.. Therefore I would check for a bent frame. Also you see the lines are not straight but after the white/grey area it seems hight is different....
Type: Posts; User: PA5RR
The lines in the attached foto seem to be out of focus.. Therefore I would check for a bent frame. Also you see the lines are not straight but after the white/grey area it seems hight is different....
Reset scanner settings sp 5-846-09 it's odd but does help to get rid of adresbook data error. Don't you forget to set the scanner parameters again cause they are now default !
For a adresbook error reset use 5-846-09. It seems a bit odd but is THE solution !
You have to set the parameters for scanning again because they have been reset to default.
This also helps on the...
Check the paperguide which the paper passes at the entrance of the fuser, probably you will find toner and papersmudge .Paper gets stuck to this rim of dirt....
Just clean it with a sharp knife or...
Do NOT try this !
You will end up with SC calls for the fuser....
Install the proper parts, otherwise your customer won't be a happy customer....
Then why don't you take my advice? Check band/flatcable laserunit ! and change safetyswitches above the fuser.
Why didn't you tell us in the first tread? In that case you should replace the exit and hight switch of the second tray.And also change the lower tray motor..Better be sure to fix it in one visit...
Ricoh has put a wrong motor in the sr790 made since april 2010...so you will have jams at R1 to R4 with no paper...
Replacing the traymotor (up and down movement) with a new one is the solution.
Itīs the frontsafetyswitches located at the rightside above the fuser...Replace them first...
Stil the same paperjams showing...then you should check the flatcable from the laserunit, disconnect it,...
Could you probably have switched the printfunction offline with the button on the operating panel?????
Your originalsensors on the RADF are blocked with dust under the contactarea. This is a strip of metal and the contactfingers slide over it. I have encountered this problem a few times, always dirty...
The solution is to disable SMB2 on the server, then the protocol is reset to SMB1 and you can acces the shared folders you created to scan to.
Here is a quote from a manual how to do so...I believe...
Our experiance with Ricoh Wireless is......it sucks....The range is so limited that you can also stick the standard supplied UTP in !
Hope you can get it to work, pinging the SMTP will tell you yes...
Nope, won't work..
Has this machine a fax installed?
Could be such a weird error from the fax-unit....
I service these models and am really disappointed that Ricoh fitted these machines with such rubbish papertrays (1 + 2)
BUT.... since paper is not bleeched anymore, paper is whitened with additives....
I would go for the one-way blue gear as well, BUT there could be a tiny piece of paper sticking in the duplex . I usually take a piece of cardboardpaper and stick it in the duplex and manually turn...
Hi all,
Overhere in the Netherlands we have a custom colorprofile for this machine.
Photo's are printed much more realistic compared with standard profile.
I do not have it but maybe when you...
Yepp I did but did you read the messages above? (by delanod)
Make sure you initialize the adresbook again, otherwise scan2folder and/or scan2mail won't work.
You can add an adres, but the scans dissapear into oblivian....
So initialize !
The replacement of...
Most likely the front bushing is broken but it could also be the rear.... When you replace the bushing, secure the position of the regroller so it wil not be pushed out on the other side ! It 's a...
I my opinion this is a TECH forum, not a saleschannel....
I have had this error many times, frontsafetyswitches yes, maybe but you should check the bandcable from the laserunit.
Pull it out and reseat it on the laserunit and do the same on the board and 9...
Your fuser is out of order you have to repair it then reset the error by a special SPmode
If you're a tech you will find out the code if you're not.....too bad
please make a scan of the garbage copy and post here so we can see....